Table of Contents
How do I control my Trane thermostat?
Manual Control Step 1: Press and hold the ‘System Mode’ button. Step 2: To set the input temperature setting, all you have to do is push the up or down buttons. Step 3: If you wish to override the manual temperature, Press the Hold button on the thermostat.
How do you reset a Trane thermostat?
All Thermostat Models MAKE SURE THAT THE HVAC SYSTEM IS IDLE BEFORE PROCEEDING! Locate the switch for your thermostat in the breaker box. Flip the switch to the OFF position for 20-30 seconds. Return the switch to the ON position. The reboot process will take several minutes to complete.
Why is my Trane thermostat not working?
Your thermostat/control may be off or set incorrectly. Check temperature setting on thermostat/control. If no change, contact your local Trane Dealer. In the meantime, try turning off your thermostat/control for 1 to 3 hours to see if it will reset itself.
How do you turn off the schedule on a Trane thermostat?
Disable Schedules From the Thermostat: Press Menu on your XL824/850/1050 thermostat. Select Schedules & Presets. Tap the On/Off toggle at the bottom of the screen to enable or disable schedules. You can tap it again to revert. NOTE: The thermostat may take several seconds to apply the change. Press Home to exit.
How do I know which Trane thermostat I have?
Finding the model number of a thermostat is easy. It should be printed on the back of the face-plate.
How do I reset my Trane Nexia thermostat?
Rebooting the thermostat will not remove any previous settings stored in the thermostat. MAKE SURE THAT THE HVAC SYSTEM IS IDLE BEFORE PROCEEDING! On the physical thermostat, press Menu. Tap Settings. Select Reboot and allow the thermostat to shut down and restart.
What is hold on Trane thermostat?
By pressing “Hold”, your thermostat will lock in the temperature it’s currently at until you change it again. When you are ready for your normal schedule to resume, simply press the “Run” button and return to your typical programming.
Why is my Trane thermostat not heating?
ANSWER: Your thermostat may not be calibrated properly or set too low. Make sure your thermostat is set to heat. Try setting the temperature 2 to 4 degrees above room temperature. ANSWER: Clean or replace your filters.
Where is the reset button on a Trane furnace?
Turn off the power and open up the control panel to access the reset buttons on these models. Next, lift the cover to the blower compartment, and you should see the reset button sitting next to the blower motor and blower wheel.
Why is my thermostat not working?
There simply may not be any power going to your thermostat. This could be caused by a poor connection, blown fuse, dead batteries, or a tripped circuit breaker. If all of these areas look good and your unit should be receiving power, the issue lies elsewhere.
How do I fix an unresponsive thermostat?
If the thermostat is still unresponsive, make sure the breaker is shut off and remove the cover. If it looks dirty inside, use canned air or a soft artist brush to clean away accumulated grime that may be affecting its functionality. Then look for issues like loose wiring or terminal screws and tighten them up.
Why won’t my thermostat light up?
Thermostat Batteries Died and Need to be Replaced If your thermostat is blank, the first thing you should do is check the batteries. Chances are, the batteries have died and the thermostat simply can’t power on. Replace the batteries and see if your thermostat turns on.
How do you read a Trane AC model number?
Trane Model Number Location First letter. Second letter. The third letter represents the product type. The fourth letter equals the product family. The seven and eight number indicate size in tonnage. The nine letter represents the major changes. Number ten indicates the power supply voltage.
How do you decode a Trane furnace model number?
How to Decode First letter: The model number starts with 4. Second letter. The next 3 letter represents the product type. The fifth number is for unit’s Seasonal Energy Efficiency Ratio. The six letter. The seven and eight number indicate tonnage. The nine letter represents the age.
How do I tell what year my Trane unit is?
The Year of manufacture is coded in the first digit of the serial number. The Month of manufacture is coded in the second letter of the serial number.
How do I unlock my Trane thermostat?
Unlocking your TraneThermostat Examine your thermostat and find both the (+) and (-) buttons. Put one finger on the (+) and one finger on the (-) button. Press these buttons at the same time. Hold both buttons down for approx. five seconds and then release. Your thermostat should now be unlocked.
Do all thermostats take batteries?
Many thermostats still use batteries, while others draw power from your home’s electrical or HVAC system. The typical battery-powered dial, switch, digital or programmable thermostat is going to take regular AA or AAA alkaline batteries, a button-style 3V lithium battery or a 9-volt battery.
Does Trane xl624 thermostat have a battery?
There is no back up battery. The user manual does not provide instructions to reset. You must look for the instruction to reset from Installer’s Guide. To download Installer’s Guide, search for the pdf file from… see more.
