Table of Contents
How do I know which circular saw blade to use?
Standard circular saw blades are typically used to cut wood or wood composites. The number of teeth on the blade helps determine the speed, type and finish of the cut. Blades with fewer teeth cut faster, but those with more teeth create a finer finish. Gullets between the teeth remove chips from the work pieces.
How many teeth do I need on my circular saw blade?
A 40-tooth blade works fine for most cuts through plywood. Blades with 60 or 80 teeth should be used on veneered plywood and melamine, where the thin veneers are likely to blow out on the underside of the cut, a characteristic known as tearout. MDF requires even more teeth (90 to 120) to get the cleanest cut.
What are the 3 basic types of circular saw blades?
They are: Rip Blades, Crosscut, Combination and Specialty blades. Ripping saw blades are designed primarily to achieve a smooth, clean and safe cut when ripping wood or cutting in the same direction as the wood grain.
What saw blade makes the smoothest cut?
With fewer spaces between the teeth, crosscut blades remove less material, resulting in a smoother cut. It also means it takes these blades longer to move through wood. Crosscut blades are an excellent choice for finish carpentry and other applications that require precision and a smooth finish.
What size circular saw will cut a 4×4?
The best way to cut a 4×4 post is by using a 12-inch miter saw, 10-inch radial arm saw, both of which can cut completely through a post in one pass, or a standard circular saw that can make precise cuts in two passes with the help of a simple jig.
Can I use a bigger blade on my circular saw?
Can I use larger blades? Short answer: No. Long answer: You should only ever use larger circular saw blades, when the difference is fairly negligible (1 mm / 1/16″). The reason for that is that for safety reasons most saws are built to tight tolerances.
What is the most common circular saw blade size?
The most common blade diameter is 7-1/4 inches. Most saws with blade capacities of 6 inches or more can cut through 2-inch dimensional lumber at a 45-degree angle in a single pass. A 5-3/8-inch saw can cut through 2-inch dimensional lumber in one pass at 90 degrees but requires two passes at 45 degrees.
What is a 60 tooth saw blade used for?
It’s better suited for cutting melamine, chipboard, and plywood. Usually 60 to 80 teeth (on a 10″ blade) with shallower gullets between teeth and a more gentle forward rake around 10°.
Can I use a smaller diameter blade on my circular saw?
While you can certainly use a smaller blade in a circular saw – as long as you keep it within reason, you might also be wondering if you can use a bigger blade in a circular saw. A larger blade will put excess stress on the motor, and may not have enough strength to provide the cutting power at the tooth you need.
Are Diablo blades worth it?
The consensus is that Diablo saw blades balance great quality with excellent value, and are a good choice when replacing or upgrading the OEM blades that are often bundled with new saws. These blades were used and tested with a Dewalt DW745 table saw, and a Makita LS1016L sliding compound miter saw.
What size blade does a Ryobi circular saw?
Blade Size: 6-1/2 in.
What is a finishing blade used for?
Finishing blades are designed for making clean and precise cuts on parts of the wood that will be visible when the job is completed. To achieve this, they have a larger number of teeth and are intended for making extra-smooth cuts that don’t damage the wood.
What type of saw blade is best for ripping hard abrasive timber such as oak?
The best saw blade for ripping hardwood is a rip blade. This blade is specially made for cutting through wood fibers, so it will cut through hardwood easily and leave a clean edge. Rip blades usually have 10 to 40 flat-topped (FT) teeth, which is a comparatively small number, but it will move through the grain quickly.
Do circular saws come with blades?
Blades. Most new saws come with a carbide-tipped all-purpose wood-cutting blade. If the saw comes equipped with a simple high-speed stainless steel blade, it’s low price might not be such a bargain; you probably will want to replace it with a more expensive carbide-tipped blade almost immediately.
Are Diablo and Freud the same?
Freud and Diablo Background The Freud Group is a global supplier of circular-saw blades, router bits, and cutters for enthusiast woodworkers, professional and industrial users. They produce under both the Freud and Diablo brands.
Can a 10 inch blade cut a 4×4?
It may surprise you to know that the answer in question to cutting 4×4 posts with a miter saw is a hard, YES! If you can give the blade more clearance, then it should be possible to get a clean single pass cut through a 4×4 post, even when utilizing a 10-inch blade.
How deep can a 6 1 2 inch circular saw cut?
The 18V Brushless Lithium Ion 6-1/2 Inch Deep Cut Circular Saw (C18DBALQ4) is a revolutionary cordless circular saw utilizing a 6-1/2″ blade which allows a 2-19/32″ cutting depth, making it one of the deepest cutting cordless circular saws on the market. This circular saw has a similar cut capacity as a 7-1/4″ saw!.
