QA

Quick Answer: What Do You Put On Epoxy After Sanding

Step by step instructions: After sanding, apply the polishing compound across the entire surface of the resin. Rub the compound into a small piece of resin using a microfiber cloth. Use a buffing wheel (or any polishing tool) to polish a larger piece of resin.

Does epoxy need a top coat?

We highly recommend applying a clear top coat to your epoxy floor. That’s why we highly recommend applying a top coat to your floors. Simply doing that will provide more durability and wear, which will reduce hot tire lift and other impacts.

What oil do you use for epoxy?

Most oil-based finishes should adhere to the epoxy or at least form a film overtop, which can clear it out after sanding. The optimal grit for most finishes is 320 or higher. Proven brands like Osmo, Rubio, and Odie’s oils/waxes have been used with great success by many customers.

How many coats of epoxy do you put on a tumbler?

It does depend on what you’re creating, but the average is 2-3 coats. To properly seal all the layers beneath, we recommend using a topcoat of your resin. For a sparkling finish, you can mix in glitter from our friends at Alumilite to realize your epoxy glitter tumbler vision.

Why is my epoxy not smooth on my tumbler?

It is caused by the resin and hardener not catalyzing properly, which means that the two parts were either not mixed thoroughly enough, or their mixing ratio was off. To avoid curing issues: Use fresh resin and hardener. Mix the resin and hardener thoroughly, scraping the sides and bottom of the container as you go.

How do you keep vinyl from peeling off tumblers?

Before you start, make sure your stainless steel tumbler or mug has been cleaned and dried. And clean the cup with rubbing alcohol. This helps to remove any remaining grease or residue that will prevent the vinyl from adhering properly. Let the vinyl cure on the cup for 48-72 hours to make sure it sticks well.

Why is my epoxy fisheye?

When a coating is applied to a substrate that is contaminated with low surface energy particles such as oil, wax, grease, or silicone, fish eyes may develop in the coating as it is applied. These fish eyes are produced because the coating is unable to wet out the contaminated area.

How do you fix epoxy mistakes?

If you do encounter an uneven finish with your epoxy resin, how can go about fixing it? A good rule to follow is to mix a little bit more epoxy than you need, ensuring you cover your surface completely. So, if your epoxy has already cured properly, you will need to sand down the surface and apply a second coat.

What causes fish eyes in epoxy tumblers?

Substrate contamination is the most common problem that causes fish eyes and pin holes in epoxy seal coats. Dust, dirt, wax, silicones, even the oil from your fingers when touching the part prior to sealing with epoxy will deter epoxy resins from laying flat and curing with a perfectly smooth surface.

What can you put on top of epoxy?

Polyurethane is a good sealant, and you can confidently put it over epoxy. You’ll need two to four coats of poly to make your project shine. However, the type of polyurethane you use (whether oil/water-based) is suited for the project for them to last and perform together.

Does epoxy need sealer?

Because the clear coat acts as a sacrificial layer, the epoxy color coat will be protected. Without it, the colored epoxy coat can lose its luster from wear.

What is epoxy sealer?

Epoxy sealers form a high-build protective film on the concrete surface, producing a hard, long-wearing, abrasion-resistant finish. Epoxy sealers are much harder than acrylics. Water-based epoxies bond well to concrete and provide a clear finish, but they are nonporous and do not allow trapped moisture to escape.

Can you oil over epoxy resin?

Waterlox Original Tung oil finishes can be used overtop of dried and cured Epoxy as long as it is lightly sanded first. There should not be adhesion issues with the epoxy; however, the film will build faster over top of it since it won’t really be soaking in like the rest of the bare wood.

Can you use mineral oil on epoxy?

It’s important to note that the mineral oil alone does not provide enough protection to withstand scratches on the epoxy. It’s recommended that you remove the mineral oil and finish with an oil- or water-based Varathane polyurethane finish or an oil-based Watco finish to protect the wood and epoxy river.

Can I epoxy over epoxy?

YES. You need to begin sanding Epoxy resin on the first coat and apply another coat, and it will bond. However, you need to ensure Epoxy underneath has fully cured – this takes about 1 to 2 days, depending on the temperature and humidity levels.

Why is my epoxy not shiny?

Cloudy or dull epoxy is typically caused by excessive moisture. Specifically, moisture from excessive humidity in the area where the epoxy was applied or excessive moisture in/on the concrete application surface. Be sure to eliminate all water before applying epoxy. Never apply epoxy when relative humidity is over 75%May 13, 2019.

Can I use toothpaste to polish resin?

Using the sponge pad of your polish machine, polish the epoxy with the toothpaste. Make sure that you don’t apply too much pressure or the epoxy might burn. Let the pad gently touch the epoxy while spinning. When you run out of toothpaste, apply it again and spray it with some water!.