Table of Contents
If the display is flashing the word EMER it indicates that your thermostat is in Emergency Heat mode and that the Emergency Heat is currently running. Emergency Heat is a backup heating system commonly used with heat pump systems. When in Emergency Heat mode your heat pump compressor will not be activate.
Whats the difference between Emer and heat?
The supplemental heat is also referred to as second-stage or back-up heating, with first-stage being the Heat Pump only. Emergency Heat is when you use your supplemental heat (2nd stage) by itself, without the use of your heat pump (1st stage heat).
Is it OK to run emergency heat?
Short answer: No. Switching your thermostat to emergency heat or “em heat” just because it’s cold outside will just raise your energy bills like crazy. Don’t use emergency heat mode unless your heat pump stops heating your home altogether. If that happens, contact a professional heat pump repairman for help.
When should you switch to emergency heat?
Emergency heat is ideal for when the outside temperature is too cold for your heat pump to keep your home warm. If the heat pump freezes over or becomes damaged, then you should switch to emergency heat and call an HVAC service provider.
Why is my thermostat on emergency heat?
Short for “emergency heat,” it is a setting that controls your home’s back-up heating system. If you have an emergency heat thermostat setting, you likely have a heat pump, as well as a gas, oil, electric, or hot-water back-up system. Now, instead of working with your main heat pump, your backup is working solo.
How do you know if your emergency heat is on?
Emergency Heat Mode Comes with a Red Indicator Light: When you turn your emergency heat on, you will see a red indicator light. This light tells you that your HVAC system is now operating in emergency mode, and it will remain on until you deactivate your emergency heat.
Why is my heat not shutting off?
One of the most common issues is the thermostat. The wiring, switches, or heating sensors can fail on your unit. A faulty check valve could be the cause of this type of heating system to fail. If your heating system will not shut down, then you need to call a professional technician for help.
How much more expensive is it to run emergency heat?
As you can see, there is a severe increase in the cost of $163.80 per week when the emergency heat is in use in extremely cost weather.What You Should Know About Heat Pumps and Emergency Heat. Cost Breakdown Normal Operation at 30 Degrees for 1 week Emergency Heat Operation at 10 Degrees for 1 week Watts per hour: 3000 watts 3000 watts + 15000 watts.
What temperature should you set your thermostat in the winter?
For winter, the ideal thermostat temperature is 68 degrees Fahrenheit when you’re at home. Energy.gov 68 degrees is a good room temperature while you’re awake at home, but recommends lowering it while you’re asleep or away. Lowering your thermostat 10-15 degrees for eight hours can reduce your heating bill by 5-15%.
Why is my emergency heat blowing cold air?
Defrost mode basically means your heat pump temporarily switches to cooling mode. This forces the outdoor coils to heat up, melting any frost or ice that has built up. And because the heat pump switched to cooling mode, it will blow cold air into your home for a few minutes.
Should fan be on auto or on for heat?
Keeping your fan on AUTO is the most energy-efficient option. The fan only runs when the system is on and not continuously. There is better dehumidification in your home during the summer months. When your fan is set to AUTO, moisture from cold cooling coils can drip and be drained outside.
Why is my emergency heat not working?
Check your power source—a tripped circuit breaker or blown fuse could be the reason for your furnace failure. Reset your breaker or replace the fuse to see if that restores heat. Check your filter—if it’s so dirty that your system is struggling to move air through it, your furnace could overheat and shut down.
Should I run my heat pump on emergency heat?
Short answer: You should only set your heat pump’s thermostat to “emergency heat” when your heat pump stops heating altogether. Otherwise, just keep your thermostat set on “heat.” There is no temperature to switch it over to emergency heat, even if your heat pump is running constantly due to cold weather.
Why does my heater smell when I turn it on?
A burning smell when you first turn your heater on is most likely caused by dust buildup on your furnace. When you turn it on for the first time after not using it for a while, this dust begins to burn off, oftentimes causing a burning plastic smell in the house.
What is the purpose of the discharge line thermostat?
The discharge thermostat is a temperature sensing safety device that turns power off when the compressor discharge temperature exceeds 240°F.
How do I know if my thermostat is bad?
7 Signs You Need to Replace Your Thermostat Your HVAC Keeps Turning On or Off. Faulty Thermostat Readings. Suspiciously High Energy Bills. Constant Temperature Shifts. Thermostat Is Too Old. Thermostat Fails to Respond to Changed Settings. Your HVAC System Short Cycles.
Why does my heat keep running?
In general, fans on thermostats have two settings: on and auto. If your thermostat’s fan setting is set to “On,” the fan will run all the time, even if the heating equipment isn’t warming your home. Other fan setting that may cause the device to constantly run include “Manual,” “Low,” “Medium,” and “High.”.
How long is a thermostat good for?
They generally last about 10 years but can last longer depending on the make, model, and type of thermostat. Over time, these systems start to age and a thermostat may malfunction because of normal wear and tear, dust accumulation, wiring issues, and rusting.
