QA

Question: What Does Rough In Size Mean

Start by measuring the rough-in size. This is the distance between the wall behind the toilet and the center of the drainpipe or the bolts that hold the toilet to the floor. It’s best to perform this measurement before you remove the old toilet.

What does 12-inch rough-in size mean for toilets?

The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″. Rear-outlet toilets are configured a bit differently.

What size toilet rough-in do I need?

The average length of any toilet rough-in should be 10, 12, or 14 inches. A 12-inch rough-in is the standard, but it’s not uncommon to find bigger or smaller toilets.

Can you replace a 14 inch rough-in toilet with a 12-inch rough-in toilet?

Every toilet rough-in can be replaced. If you have a 14-inch rough-in, you can replace it with a 12-inch rough-in. The only problem when you do that, is that you will have a 2-inch gap between the toilet tank and the wall.

What is rough opening size?

Framing rough opening sizes are really quite simple. Just add 2″ to the width of the actual door size. You should add 2-1/2″ to the height of the actual door. The height is 80″ (which is considered 6/8 or 6′-8″) add 2-1/2″ to the actual door height and frame it 82-1/2″ high.

How much bigger should a rough opening be for a window?

Recommended rough opening is between 3/4″ (19mm) – 1″ (25mm) larger than the window width and height. Ensure that the rough opening is plumb, level and square, and the walls in the opening are not twisted.

Can you replace a 10-inch rough in toilet with a 12-inch rough in toilet?

The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.

How do I know if my toilet is a 10 or 12 rough?

If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.

What is the difference between a 10 and 12 rough in toilet?

When a toilet with a 10-inch rough-in is placed in a 12-inch rough-in space there will be 2 inches of open space between the tank and wall. However, the extra inches will cause the tank to be further away from the shutoff valve on the wall, so a longer connector may be needed to reach effectively.

How do I know what size toilet to buy?

To measure the bowl shape, you can start by putting your measuring tape at the back of the toilet, and extend the tape forward to the end of the bowl, measuring parallel to the floor. The most important measurement you can take for a replacement toilet is the rough-in dimension.

How far from the wall should a toilet rough-in Be?

The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall. Don’t measure from the base molding! Take this measurement from the finished wall.

How far should a toilet be from a vanity?

Toilet placement A toilet should have some elbow room between it and another fixture or vanity. The NKBA’s recommendation is at least 18″. Codes allow a minimum distance of 15″.

Does toilet rough-in size matter?

For a standard toilet, the rough-in measurement should be between 11 inches and 13 inches. If the rough-in measurement is not between 11 inches and 13 inches, a standard toilet will not fit the space, and you will need to look for a toilet designed for that specific rough-in distance.

Can you replace a 13 inch rough-in toilet with a 12 inch rough-in toilet?

That’ll be your rough-in. If your distance if 13″ and you have a 1″ gap between the tank and the wall, then yes, your existing toilet is probably a 12″ toilet. You can indeed have two 12′ toilets that differ in size from one another.

How many inches does an offset toilet flange move?

The typical offset is 12-inches for most residential toilets. As a result, the toilet had 4-inches behind the tank. It looked like it was trying to participate in the activities of the bathroom rather than sit quietly until needed.

What is the rough opening for a 28 inch Prehung door?

Measurements For Rough Opening Rough Opening Width Rough Opening Height Door Size to Order 27.75″ – 29″ 81.5″ – 83″ 26″ 29.75″ – 31″ 81.5″ – 83″ 28″ 31.75″ – 33″ 81.5″ – 83″ 30″ 33.75″ – 35″ 81.5″ – 83″ 32″.

What size rough opening do I need for a 30 inch door?

32-1/2 inches. The rough framing should be 2-1/2 inches wider than the door itself. That leaves room for the 3/4 inch finish frame on each side of the door, and then 1/2 inch on each side for the shims between the finish frame and the rough frame.

What is the rough opening for a 72 french door?

Standard interior French doors measure 80 inches high by 36 inches wide per door. Interior french doors side by side usually have a width of 36 inches. This size will create an overall door opening that’s 72 inches wide.