QA

Quick Answer: What If I Have Two Black Wires

You will get a reading if one wire is hot and the other isn’t. However, if both wires are hot, the reading will be zero. However, if you need to rewire a light switch or a plug socket, you may occasionally come across two black wires. It’s essential that you determine which black wire is hot before proceeding.

How do you wire a light with two black wires?

Connect the top screw to the wire that feeds to the light. Connect the bottom screw to the hot wire. When you turn the power back on, and if you want to swap the direction of the switch (as in press down to turn off, or turn on), turn off the power and switch the two black wires.

Which wire is hot if both are black?

Here’s a rundown of electrical wires: The black wire is the “hot” wire, which carries the electricity from the breaker panel into the switch or light source. The white wire is the “neutral” wire, which takes any unused electricity and current and sends them back to the breaker panel.

Why does my light switch have 2 black wires?

The bare or green-wrapped ground wires serve as a backup to divert the power safely away in case of an electrical fault. In most cases, two black wires will be attached to the switch’s two terminal screws. The ground wires will be connected to each other and attached to the grounding screw on the switch.

What to do when you have 2 black wires?

You should see two black wires, each connecting to a different screw on the right side of the switch. These are called terminal screws. You should also see a green wire, called a ground wire, which attaches to a screw on the lower-left side of the light switch.

Why do I have 2 black wires and 2 white wires?

Each lightbulb socket must have a separate black and white wire to supply electricity to the lightbulb; the more lightbulbs, the more wires. Connect the two black wires from the light fixture to the black wire from the electrical box the same way you connected the white wires.

Can you connect 2 black wires together?

Just go ahead and connect the new dimmer the same way. This is the typical way to connect a switch. The 2 blacks connected are “power in, power out” to the next switch in the circuit.

Why does my light switch have 3 black wires?

If the light turns on, the second black wire you connected to the switch is the switch feed and the unconnected black wire is the feed to the other loads. If the light doesn’t turn on, then it’s the other way around: the connected wire feeds the other loads and the disconnected wire is the light feed.

Which wire is hot if both are clear?

If the plastic is clear, the wires in the neutral side are silver while those in the hot side are copper.

Is black wire positive?

The black wire is positive, the white wire is negative, and the green wire is the ground.

Can a light switch have two hot wires?

2 Answers. The wire from the other switch is almost certainly the line hot. If so, it will be always hot no matter what position either of the switches is in. This is electrically the same as having a separate wire going to each switch from a common line hot.

What if my light switch has no ground wire?

Grounding light switches have become commonplace, used as a preventative safety measure. It is perfectly legal to wire a light switch without the inclusion of a ground.

Why would an outlet have 2 hot wires?

The reason for multiple hot/neutral wires for one outlet is that the outlets are daisy-chained together. This means hot/neutral is only coming from one of the wires and it is being sent to the other wire.

What happens if you mix up hot and neutral wires?

This happens when the hot and neutral wires get flipped around at an outlet, or upstream from an outlet. Reversed polarity creates a potential shock hazard, but it’s usually an easy repair.

What happens if you reverse black and white wires?

When the wires are connected properly at the electrical panel and terminated correctly at the receptacle, all is fine. If the white and black wires get swapped somewhere along the way, trouble may be right around the corner.

What if I have two white wires?

You likely have a switch loop. You should find which one is hot when the switch is on (mark it black with electrical taps) and connect that one to the black wire of the fixture. The other white should connect to the white of the fixture. The ground should be connected to the bare wires (ground) in the box.

Why do I have 2 white wires?

Could be 2 whites if the person wiring it did not follow convention and use a white to go to the switch so black could come back. As posted elsewhere if it’s 2 whites then you need to determine which is hot and which is neutral, then put a piece of black tape on the hot one for future reference.

Can you pigtail black wires?

When making a pigtail, choose a scrap of wire with insulation that is the same color as the circuit wires you are connecting: white pigtails when connecting to neutral wires, red or black when connecting to hot wires, green or bare copper when connecting to grounding wires.

Can you pigtail red and black wires?

If you see a red wire spliced together with a black one in a 120-volt outlet, it’s probably because the outlet is powered by a wall switch. Certain switch loop configurations require a three-conductor wire — the extra wire is needed to complete the circuit at the switch.

Why does a switch have 3 wires?

A 3-way switch makes it easy to turn on a light fixture from two separate locations in the home. Wiring one is slightly different from wiring a single-pole switch. In a standard, single-pole switch, one light switch controls one light fixture—on/off.

What happens if I wire a light switch backwards?

But here’s the catch: If you connect the circuit wires to the wrong terminals on an outlet, the outlet will still work but the polarity will be backward. When this happens, a lamp, for example, will have its bulb socket sleeve energized rather than the little tab inside the socket.

Which black wire is hot on a light switch?

Which wire is hot if both are black? The black wire is the “hot” wire, which carries the electricity from the breaker panel into the switch or light source. The white wire is the “neutral” wire, which takes any unused electricity and current and sends them back to the breaker panel.

Which wire is live when both are same color?

Identify the neutral wire in the fixture by looking at the wires. In most modern fixtures the neutral wire will be white and the hot wire is red or black. In some types of fixtures, both wires will be the same color. In this case, the neutral wire is always identified by some means.

Is black wire positive and red negative?

One is marked positive (+), the other negative (-). There are also positive and negative cables in the jumper cable set. The red one is positive (+), the black one is negative (-). Never connect the red cable to the negative battery terminal or a vehicle with a dead battery.