QA

Quick Answer: What Is 12/3 Wire Used For

ROMEX® 12/3 wire is used in buildings for circuits that use higher amperage than the standard 20 amps. Most people are not familiar with this type of wire because it is used to hook up heavy-draw appliances such as water heaters and central air conditioning.

What is the difference between 12 2 wire and 12 3 wire?

The designation 12/2 indicates AWG 12 wire with two conductors (AC hot and AC neutral), 12/3 indicates AWG 12 wire with three conductors (two AC hot and AC neutral). Both designations also typically include a smaller bare copper earth ground conductor.

What can 12 2 wire be used for?

14-2 can only be used for 15A circuits. 12-2 can be used for 15A circuits or 20A circuits. If you are in the US, you can use 12-2, a 20A breaker, and 15A receptacles (as long as you have more than 1 receptacle on the circuit). Its fine for 15 or 20 Amps.

How far can you run 12/3 gauge wire on a 20 amp circuit?

Originally Answered: How far can you run 12 gauge wire on a 20 amp circuit? About 400 feet. After that voltage drop is a factor and the gauge will have to be increased or the voltage increased.

Can I use 12 3 wire for a stove?

1 Answer. Not even remotely close. You need 8 gauge copper or 6 gauge aluminum wire.

When should you use 12/3 wire?

ROMEX® 12/3 wire is used in buildings for circuits that use higher amperage than the standard 20 amps. Most people are not familiar with this type of wire because it is used to hook up heavy-draw appliances such as water heaters and central air conditioning.

Can I use 12 gauge wire for lights?

If you’re wiring a circuit on which there are both lights and outlets, or you just aren’t sure which wire gauge to use, you can’t go wrong by choosing a 12-gauge wire. It’s not quite as flexible as a 14-gauge wire, and it costs a bit more, but it’s always a safe choice on a 15- or 20-amp circuit.

Is it OK to use 12 gauge wire on a 15 amp circuit?

Because it has even less chance of overheating, 12-gauge wire is also acceptable on a 15-amp circuit.

How many watts can 12 3 wire handle?

It is more than 5000 watt at 20 and0-240 volts.

Which wire is best for house wiring?

If what you need the wire for is the wiring of your home, copper wires will be most appropriate for you. Copper is more conductive than aluminum but is also heavier and more expensive.

What is code for buried electrical wires?

Low-voltage (no more than 30 volts) wiring must be buried at least 6 inches deep. Buried wiring runs that transition from underground to above ground must be protected in conduit from the required cover depth or 18 inches to its termination point above ground, or at least 8 feet above grade.

What cable do I need to run power to my shed?

One of the most frequently asked questions is what outdoor electrical cable do I need to power my shed? The answer is armoured cable.

What size wire do I need to run 300 feet?

for 300 feet for 100 amp rated service I would use Aluminum direct burial 1/0-1/0-1/0-1/0, the forth can be as low as #4 for the ground (but also in conduit, even if in conduit must still be rated underground wire and required by code also) Also note the size wire the breaker can handle, cannot cut strands to make fit, Jul 28, 2014.

What size wire is used for hot water heater?

Electrical wires Since the generic breaker size for water heaters is 30-amps, the best wire size is a #10 American Wiring Gauge (AWG). I suggest you use a 10-2 Non-Metallic Cable (NMC) for a 30-amp 240Volt circuit.

What size wire do I need for 50 amp?

50 AMP Wire Size For a maximum of 50 amps, you’ll need a wire gauge of 6. Fifty amp breakers are most often used to power many different appliances. However, a kitchen oven can alone require 50 amps. Many electric dryers also require a 50 amp breaker.

What size wire do I need for a dryer?

The NEC requires that dryers have a dedicated circuit with a minimum of 30 amps. This calls for a 30-amp, double-pole breaker wired with 10 AWG wire.

Can you use 12 3 wire for a dryer?

It’s fine for the dryer. The washer was paid for on 12/2. A 220v/30 Amp Dryer circuit would use 10/3 with ground.

What kind of Romex is used for outlets?

The following NEC regulations apply to Romex conductors: Wire Gauge or Type Rated Amperage Common Uses 14-2 Romex 15 A Lighting Circuits 12-2 Romex 20 A Lighting and Outlet Circuits, refrigerator 10-2 Romex 30 A Electric water heater, baseboard heaters 10-3 Romex 30 A Electric Clothes Dryer.

What size wire is used in houses?

Wire Gauge The most common sizes you’ll find in residential work are 14-gauge and 12-gauge. Larger appliances such as electric stoves, electric water heaters, electric dryers and central air units will often use 10-, 8- or even 6-gauge wire.

How far can you run 12 gauge wire on a 20 amp circuit?

You can run a 12 gauge wire up to 70 feet on a 15 amp circuit. That number drops to 50 feet if you run 12 gauge wire on a 20 amp circuit.

Is 12 gauge wire always yellow?

Yellow color-coded cable sheathing encloses 12-gauge wires. Yellow 12-gauge cable is typically used for 20-amp circuits that power general household outlets used for a variety of plug-in appliances. Dedicated appliance circuits also call for 20-amp circuits in most cases.

Can you use 12 gauge wire for outlets?

Using a 12-gauge wire is a safe bet for wiring a circuit that includes both lights and outlets, or if you’re not sure which gauge to use. It is more expensive and less flexible than 14-gauge wire, but it is always a good idea to use it on a circuit rated for 15 or 20 amps.

Can you mix 12 gauge and 14 gauge wire?

Originally Answered: Can I mix 12 and 14 gauge wire? The 12 gauge can carry more current, therefore; you must not use 14 gauge in place of 12 gauge, but you can use 12 gauge in place of 14 gauge, but 12 gauge is larger.

What size wire do I need for a 1500 watt heater?

1. Chart For What Size Wire For A Baseboard Heater 240 Volt 500 watt 240 v 12 Gauge 1000 watt 240 v 12 Gauge 1250 watt 240 v 12 Gauge 1500 watt 240 v 12 Gauge 1750 watt 240 v 12 Gauge.