QA

Question: What Is A Worm Drive Saw

What is a Worm drive saw? A worm drive saw has the motor attached at the rear. This is very powerful and its power is driven through two gears each set at 90 degrees. This setting implies that the engine produces more torque but less Rotation Per Minute (RPM) of about 4,500.

What is the purpose of a worm drive saw?

Advantages of a Worm Drive Circular Saw The longer distance between the handle and the blade extends your reach while making a cut, which is helpful for crosscutting sheet goods. A worm drive also has larger gear teeth with more load-carrying capacity than a direct drive, which provides more power but also adds weight.

What are the benefits of a worm drive?

Longer lasting, great sightlines for many users, more torque, accuracy and power – these are top advantages of the worm-drive power saw. The main drawback is the weight issue.

Is worm drive table saw better?

The extra torque from a worm drive is excellent for the higher-stress rip cuts that a table saw has to endure by nature. The trade-off is typically some additional weight and a slower blade speed – but Skilsaw has managed to buck both trends.

What’s the difference between a worm drive and a regular circular saw?

Regular circular saws have an RPM of 6,000 or higher while worm drive saws have an RPM of not more than 4,500. This difference of RPM is however balanced when it comes to torque. Worm drive saws offer more durability and power because they have larger teeth which have a more loading capacity than regular circular saws.

What special maintenance does a worm drive saw require?

However, hypoid saws and sidewinder circular saws have sealed bearings and don’t require any maintenance. Worm-drive saws have an oil-bath gearbox meant to provide cooling and lubrication to the gears that transfer motor power to the sawblade. The oil eventually gets contaminated through use.

What are the drawbacks of worm gear drive?

The main disadvantage of worm drives is their low performance offered by these gearbox stages, which can be close to 15% due to the high friction and associated axial stresses.

Does a worm gear increase torque?

Worm gears can be used to either greatly increase torque or greatly reduce speed. They are also the smoothest and quietest of the gear systems, as long as they are properly mounted and lubricated.

Can I buy a worm drive saw in the UK?

DCS577N 54v FlexVolt 190mm Circular Saw Worm Drive Style The DCS577 will be the first Cordless Worm Drive Style Saw to touch down in the UK & Europe, which will make it an extremely popular launch. Worm saws are commonly designed with a left-handed blade which most users will find more convenient when on the job.

Is Skilsaw a good brand?

Best Corded Worm Drive Circular Saw For those of you who prefer the inline design and higher torque of a worm drive, we recommend you look at the brand that started it all: Skilsaw. The best corded worm drive circular saw is Skilsaw’s SPT 77 WML in our opinion.

What is the advantage of a rear handle circular saw?

Because of the placement of the motor, Rear Handle Circular Saws get a heck of a lot more torque than a standard Sidewinder Circ Saw. Sidewinders get more RPM’s, but the torque and power beats speed when you’re cutting into hardwoods with a Worm Drive (rear handle) saw.

What is better Sidewinder or worm drive?

Sidewinder vs Worm Drive Torque A worm drive saw has larger gear teeth with more load-carrying capacity than a sidewinder, offering more power and durability. It also allows the saw to handle higher shock loads. It has more muscle to plunge cut and handle tougher jobs.

Is there a left and right handed circular saw?

From what I’ve seen these past few years, corded circular saws are mainly right-handed saws. There are some brands, such as Milwaukee, that offer both right- and left-handed saws. Worm drive saws are typically left-handed. Cordless circular saws are typically left-handed as well.

Why are most circular saw right blade?

Blade-Right for the Right-Hander Using the saw this way will place the motor weight over the waste edge when you cut from the end-side of a board or sheet. This means the saw eventually cuts off its own support. Most users have no trouble holding the saw steady, but this can result in bind-ups.

How often do you change the oil on a worm drive saw?

How often do you need to change the oil in your worm drive mitre saw? Answer: Heavy use, oil change 60 days. Occasional or DIYers, go 2-3 years, if it just looks good in the shop, change 5 years.

Should you oil a circular saw?

Circular saws can be used for all types of wood product cutting–lumber, plywood and paneling. The saws can cross-cut and rip cut. The blade doesn’t need to be oiled very often; you can coincide the oiling with blade replacement, but a spot of oil on the inner washers will keep the saw running better and more safely.

Is worm and worm wheel reversible?

Unlike with ordinary gear trains, the direction of transmission (input shaft vs output shaft) is not reversible when using large reduction ratios. This is due to the greater friction involved between the worm and worm wheel, and is especially prevalent when a single-start (one spiral) worm is used.

Is it possible to use worm gears in cranes for lifting purpose?

Is it possible to use worm gears in cranes for lifting purpose? Explanation: Worm gears support self-locking operation and hence are advantageous to use in lifting operations.

Why is the efficiency of worm gear drive low?

The efficiency of a worm gear is also determined by the ratio of the worm gear. High ratio worm gears have a smaller gear tooth lead angle, which increases the surface contact area between the gears. The higher contact area creates more friction between the gears and causes lower efficiency.