Table of Contents
How to Mix and Apply Epoxy to a Glitter Tumbler. If you’re wondering what kind of epoxy to use on tumblers, which is a common question from beginners – I used Amazing Clear Cast brand epoxy. It comes with both epoxy part that you will need to mix together. You can also get it as part of a full epoxy tumbler kit.
What equipment do you need to make glitter tumblers?
Additional Glitter Tumbler Making Supplies – You may also want a heat gun tool and cup turner kit or way to hold your tumbler while applying glitter and epoxy. A motorized cup turner for tumbler crafts is recommended (sold separately). A cup or tumbler spinner helps keep your epoxy even. 20 resin mixing sticks.
What resin is safe for tumblers?
1. ENVIROTEX LITE EPOXY RESIN For Tumblers. Envirotex Lite is a brand of epoxy resin you can use for tumblers, whose claim to fame is that it is a pour-on, high gloss finish. It cures to a thick, glossy coating in about 8 hours at 70F, and reaches full cure in about 48 hours.
Can you use spray epoxy on glitter tumbler?
To apply the glitter, you need an adhesive. Some folks like Mod Podge, others like spray adhesive. And, of course, you need the epoxy resin to seal your glitter tumblers. This is what will keep your glitter contained and protected on your tumbler!Dec 29, 2018.
How many coats of epoxy does a tumbler need?
It does depend on what you’re creating, but the average is 2-3 coats. To properly seal all the layers beneath, we recommend using a topcoat of your resin. For a sparkling finish, you can mix in glitter from our friends at Alumilite to realize your epoxy glitter tumbler vision.
Do you have to sand between coats of epoxy on tumbler?
????TIP: Remember: whenever your resin is dry, you need to sand before you apply a second coat to ensure the two layers bond together. If you don’t sand, you run the risk of the two layers eventually delaminating.
Do you have to use epoxy on tumblers?
If you’re making tumblers, you need to be sure that the epoxy resin you’re using is food safe after it’s cured and becomes an inert plastic. There’s a lot of different epoxies out there and not all are food safe.
How do you apply epoxy smoothly?
best results are achieved by applying the epoxy evenly. The ‘roll on and tip off’ method is a great way to do this – ‘roll on’ a thin layer of epoxy with a foam roller and then ‘tip off’ by dragging another roller, cut into sections, across it to leave the surface both level and free from air bubbles.
Can you use any kind of epoxy for tumblers?
One of the questions most beginners ask is, what kind of epoxy to use on tumblers. One brand that you can use is the Amazing Clear Cast epoxy, you will find it comes in a 2-part clear coating and casting resin. There is also an entire epoxy tumbler kit available in this brand.
What is the difference between epoxy and resin?
The most noticeable difference between these two compounds is their intended use. The Epoxy Coating Resin is intended for coating surface applications, while the Casting Resin is used mainly for jewelry, molds or figurines.
Is it safe to drink from epoxy tumblers?
ArtResin is NOT edible or potable in either liquid or cured form. The maximum temperature cured ArtResin can come in contact with is 120F or 50C. Exposing ArtResin to temperatures higher than this may cause irreparable damage to the resined surface.
Do you have to seal glitter before epoxy?
Now you’ll want to seal the glitter layer with Krylon Clear Coat Spray. This just helps keep all the glitter stay sealed down enough so when you add epoxy in the next step you’re not brushing glitter all over the place. Wait several hours for the cup to dry really well before moving on to epoxy.
How long does it take epoxy to dry on a tumbler?
Let The Tumbler Cure: Leaving the motor running, allow the cup to continue turning until the resin is dry to the touch, approximately 18-24 hours later. Remove the tumbler from the cup turner and remove the tape. Allow the cup to continue curing – it will be fully cured at the 72 hour mark.
What do you seal glitter tumblers with?
Seal glitter on the tumbler with a gloss clear spray sealer or brush on mod podge. Allow tumbler to dry. 5.
Why does my epoxy tumbler have dimples?
A: Dimples can occur for 3 reasons: 1) If the temperature fluctuates in the room while the ArtResin is curing during the first 24 hours. Make sure that the temperature stays stable in the room ( 72-77F or 23-25C ) while your piece cures. 2) If you get some dust particles in your piece.
Does epoxy stick to powder coat tumbler?
The powder coating that I’m accustom to working with is a pretty inert coating and should be ok under epoxy as long as the powder coating is in good shape and adheres well to the surface. You would need to clean and prep it just like you would anything else you wanted to prime and paint. As Len has said.
How long should you wait between coats of epoxy?
When using epoxy, it can be a helpful process to add a second layer, but you want to make sure to follow the correct procedures. With most coating epoxies, if you are trying to build up to your desired thickness, it is recommended to pour your second coat once the first coat is tacky to the touch (usually 4-6 hours).
What can you use other than epoxy on tumblers?
Brite Tone – If you want ONE item to use instead of epoxy, this would be it. You want to use Brite tone on every single cup. It is the best quality top coat they have that once it is cured, is shinier and more durable than epoxy!.
Can you seal a tumbler without epoxy?
Make sure to remove the tape before the Mod Podge dries! There you have it! A way to make a decorated Yeti cup or Ozark tumbler without having to use epoxy. As you can see from the pictures, it’s not as smooth as epoxy but it still works and actually has a nice texture to it!.
What can be used instead of epoxy?
Hard plaster and concrete are excellent epoxy resin alternatives, and their use is not limited to small surfaces only. Unlike epoxy resin, concrete and plaster can be easily applied to large surfaces as well. Other great alternatives to epoxy resin include slush latex, metal, plastic, and alabaster.
