QA

Quick Answer: What Kind Of Subfloor Is Needed For Ceramic Tile

Exterior-Grade Plywood Exterior plywood is an acceptable underlayment for tile and is preferred to interior-grade plywoods because the bonding adhesives used are waterproof. If water seeps through the tile installation to the underlayment, it will not cause the wood to swell, as happens with interior-grade plywood.

How thick should the subfloor be for ceramic tile?

The subfloor under the tile should be at least 1 1/8″ thick, with a minimum of 5/8″ thick exterior grade plywood topped by 1/2″ cement backer board.

What should I put down before installing ceramic tile?

Underlayment is something you put on top of your substrate to prepare it for tiling. The substrate (or subfloor) is the ground, whether it’s made of plywood or cement. Cement board or backer board are the most standard underlayments.

Does ceramic tile need underlayment?

Some people usually ask themselves if porcelain tiles need underlayment, well yes, they do. For your porcelain tile to last for long, you need an underlayment. Both porcelain and ceramic tiles are rigid, so if they are installed on surfaces that are not flat, they can crack easily.

What should be installed over plywood before laying ceramic tile?

On a plywood subfloor, you need either a layer of cement backer board or an underlayment membrane, like Custom Building Products’ Wonderboard and RedGard, between the subfloor and tile for the thin-set adhesive to achieve a good bond.

Is 3/4 subfloor enough for tile?

Tile installed over wood floor systems MUST have a minimum of 1-1/4 inches of solid material beneath it. This means you can have a 3/4 inch wood subfloor covered by 1/2 inch plywood, cement board, or approved gypsum fiber underlayment.

What kind of subfloor is needed for ceramic tile?

Exterior-Grade Plywood Exterior plywood is an acceptable underlayment for tile and is preferred to interior-grade plywoods because the bonding adhesives used are waterproof. If water seeps through the tile installation to the underlayment, it will not cause the wood to swell, as happens with interior-grade plywood.

Can you use thinset as grout?

Thinset mortar, commonly used for securing stone to a surface becomes very hard just as a Portland cement grout becomes as it dries. Although the intended use for thinset is not for mortar joints. You can use it on backsplashes and other surfaces that will not see heavy traffic.

Can I use cement to lay floor tiles?

Generally, I would advise that you should be using a floor tile adhesive instead. Ideally having a thick layer to ensure that the tiles are laid evenly on your floor, if it is noticeably uneven. A cement/sand mixture could be a cheaper solution overall, but if you can afford it the adhesive will likely be better.

Can you lay tile directly on subfloor?

Tile can be laid on plywood. But do not install tile directly on the plywood subfloor itself. Use an intervening layer of a sheet of thinner plywood.

Can you lay tile without backer board?

As long as a concrete slab is very flat and contains no cracks, tile can be installed directly on top, using thinset as the adhesive, allowing you to skip the backer board layer. If the slab is uneven or cracked, it must first be patched and leveled before tile can be installed.

Do you have to put cement board under tile?

Whenever you’re laying tile on a wood subfloor, you need to first install cement backerboard to prevent leaks and water damage that could harm your flooring and the structure of your home. Unlike wood or drywall sub-surfaces, cement backerboard will not rot, warp or grow mold and mildew when exposed to water.

Do I need to seal plywood before tiling?

This expansion gap should be filled with a silicone sealant to prevent it from being filled with tile adhesive when fixing your tiles. Before fixing your plywood overlay, ensure the reverse and edges of the boards have been sealed using BAL Bond SBR neat, as this reduces water permeability.

Can you wall tile onto plywood?

If you are working in an interior setting in a dry area where the tile will never come into contact with water, you can install the tile directly onto the face of the plywood so long as you use the proper type of thinset.

Can you tile 3/4 plywood?

A single sheet of 3/4″ inch plywood is normally not adequate as a substrate for tile. The tile industry recommends a subfloor that’s at least an inch-and-a-1/4 thick. Underlayment should be nailed or screwed every 8 inches in the field and every 6 inches around the perimeter.

How thick should plywood be for floor tiles?

When using plywood, you’ll need to ensure it’s at least 12mm or more in thickness to create a rigid surface for your tiles. This, along with your tiles, will raise the level of your flooring, so be sure to bear this in mind before you get started.

How thick should plywood be for tile?

Plywood must be installed over an adequate subfloor and must be at least 1 1/8″ thick when combined with the subfloor. Interior-grade plywood and particleboard are not considered strong enough for a tile installation.

What kind of plywood do you use for tile subfloor?

Tip: Make sure the subfloor will not deteriorate when it gets wet. Particleboard is not an acceptable subfloor material for tiling projects. Oriented strand board (OSB) and exterior-grade plywood will work if first covered with a latex-modified mortar and a tiling backer board.

What thickness subfloor is recommended?

The recommended thickness of the plywood subfloor is governed by the spacing of the joists. Some experts suggest that 15/32-inch plywood should be standard if the underlying floor joists are spaced 16 inches apart or less, but slightly thicker 3/4-inch plywood should be used for joists spaced further apart.

What do you put on floor before tiling?

Install a cement backer board to set a good base for your tile and prevent any movement-related cracking of tile or grout. Backer board is screwed down to wood subfloor using specific backer board screws and mortared down with tile adhesive mortar plywood subfloor.

Can you tile over old floor adhesive?

You can tile over your old floor adhesive by placing a barrier down in the form of thin-set, underlayment, a false floor, or using a floor leveling compound before tile installation. To achieve the strongest bond and preserve your moisture barrier, you should scrape, sand, or strip the old adhesive.

Can you lay floor tiles on a wooden floor?

Tiling on wood. Can you tile on wood? Yes, but because wooden floors naturally bend, bounce and expand, tiles can end up cracking under the pressure if installed incorrectly. Tiling on wood surfaces is all about ensuring there is enough rigidity in the wooden subfloor and selecting the correct flexible tile adhesive.

Is thinset the same as grout?

People tend to get them confused, or even think that they’re the same thing. Thinset mortar is used to adhere tiles to a surface, while grout is designed to fill the spaces between tiles once they’ve been installed.

Is mortar stronger than grout?

Strength. When it comes to the strength of the two materials, you might be surprised to learn that grout is generally stronger than mortar. This might seem counterintuitive, as you might think the stuff needed for building brick walls would be stronger than the gap filler for the tile in your bathroom.