Table of Contents
In your lighting system, the ballast regulates the current flowing to the fluorescent lights and provides the voltage needed to start the lamps. The ballast takes in electricity and then regulates current throughout the bulbs. This is why a degrading ballast will cause the fluorescent lights to flicker.
How do I stop my fluorescent lights from flickering?
Brush dust out of sockets, then reseat firmly. If the tube still blinks when the light is turned on, wiggle it a few times while the light is on to see if this cures the problem. If not, take the tube out and inspect sockets closely to see if spring contacts are bent or corroded.
Can a bad ballast cause flickering?
Dimming or flickering If your bulbs are very slow to reach full brightness or strobe periodically, there may be a problem beyond the bulb. Water-damaged or faulty ballasts often struggle to regulate current.
How do you know when a fluorescent bulb is bad?
Look for dark areas at the base of the bulb. When bulbs age and have been used for a long time, brown spots will appear. If darkness begins to form at the ends of the tube, the bulb may be near its end. While they may still light, they are wearing out and will die soon.
How long do fluorescent bulbs last?
Typical lamp life for a fluorescent bulb is about 20,000 hours, but this can degrade as a consequence of frequent switching (turning on and off). Burning life is extended if lamps remain on continuously for long periods of time.
How much does it cost to replace a ballast in a fluorescent light?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
Why do my fluorescent lights burn out so fast?
There are many possible reasons why a light bulb burns out quickly: The power supply voltage may be too high. Bulbs may be loose or connected improperly. Excessive vibrations may be causing the filament to break.
How can you tell if a light ballast is bad?
Signs That Your Ballast is Bad Dimming or Flickering Headlights. If your HID bulb cannot produce its full brightness or strobe periodically, this is most probably a ballast problem. Strange Sounds. Headlights Not Working. Changing Light Colors. Constantly Blowing Fuse. Damaged Casing. Burn Marks. Water or Oil Damage.
How long do ballasts last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
Where is the ballast on a fluorescent light?
Locate the wiring cover plate, usually in the center of the fixture. On either side of the cover, there will be tabs that catch in slots in the fixture. Squeeze the sides of the cover inward to slip the tabs out of the slots, and pull the cover down. This will expose the ballast and its wiring.
Do both fluorescent bulbs need to be replaced?
What about pairs of fluorescent tubes? In many fluorescent fixtures, power is sent through a pair of bulbs. If either bulb is bad, they may both flicker or one may flicker and the other show no life. My philosophy of sensible repair is to always replace both bulbs.
How do you make fluorescent lights last longer?
“Turning off fluorescent lights for more than five seconds will save more energy than will be consumed in turning them back on again,” the DOE explains. However, the lifetime of your bulb is affected by the number of times you turn it on and off.
Do fluorescent lights get old?
The Shelf Life of CFL (Compact Fluorescent Lamp) Light Bulbs CFLs typically have a rated service lifespan of 6000–15,000 hours, whereas standard incandescent lamps have a service lifespan, of 750 or 1000 hours.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
Can you replace a ballast yourself?
The ballast takes in electricity and then regulates current to the bulbs. You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.
Can a fluorescent light work without a ballast?
Reverted question “ Can I make a fluorescent light work without a ballast?” yes, you can, but you need something to reduce the current as the bulb warms up. So, you can drive a fluorescent with a pulse width adjustable power supply, but this is what is in an ‘electronic’ ballast.
Why do my light bulbs keep flickering?
Contact problems, faulty wiring connections, worn-out receptacles, or a bad filament can all cause flickering. Often, these problems occur as the light bulb ages. You can try rotating a bulb in its fixture to create a better connection, but chances are, it needs to be replaced.
Why do light bulbs burn out physics?
Light bulbs burn out due to repetitive stress to the tungsten filament which produces the light. When the filament gets thin enough from repeated wear, it can snap, breaking the electrical current, and causing the bulb to burn out.
Why is my light bulb crackling?
If the bulb flickers on and off, it usually means that the switch contacts are getting bad. Usually, you’ll be able to hear a sizzling or crackling sound if the switch contacts are bad. By far the most common problem is a loose wire connection at the switch itself, which is subject to constant on-off usage.
Can a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
