Table of Contents
Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall. Cabinet doors 24-36 inches tall are best adorned with pulls 7-12 inches long, while cabinets taller than 36 inches such as pantries, built-in appliances and pullouts should be accompanied by pulls longer than 12 inches.
What size cabinet pulls do I need?
Determine Size While there is no set rule, we generally recommend that the pull length is approximately 1/3 of the cabinet or drawer width. Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter.
What is the standard size for kitchen cabinet pulls?
For standard size cabinetry (dimensions of 12″ – 36″) the most common pull sizes are 3”, 4”, 96mm, and 128mm center to center (from one screw hole to another). Standard knob sizes are 1 1/4″ or 1 3/8″.
What size cabinet pulls for 36 inch drawers?
Oversize Drawers (36″ or larger) For larger drawers, consider investing in longer-length stainless steel pulls such as 6”, 8”, 10” or even 12”. Another alternative to this is by using double smaller pulls, such as two 3” or two 5” pulls.
How do you measure for cabinet pulls?
To accurately measure existing fixing centers, open your kitchen door or drawer and measure the distance between the center of each screw. This measurement should be used when specifying your new handles.
Should cabinet pulls be vertical or horizontal?
Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.
What size cabinet pulls for 30 cabinet?
As we mentioned above, for cabinet drawers 30 inches wide or more we would recommend a pull 5 inches or longer, OR two pulls 3 inches to 5 inches long each. This is necessary because the longer a drawer gets the more weight it can hold and the harder it may be to open.
Do you put pulls on fake drawers?
I would recommend putting pulls on the dummy drawers it allows for consistency. Good design is always consistent. It will also give the illusion that these drawers are not fake. The idea of putting a minimal intrusive towel bar works well because then it will serve more for function then aesthetics.
How do I know what size drawer pulls to buy?
There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably. 5″ pulls are also an excellent choice.
How do you measure for drawer pulls?
The length of the pull is important because you want it to be proportional to the size of your cabinet or drawers. We recommend a pull that is no longer than one-third of the total cabinet door height and no longer than one-half of the total drawer width.
Can you mix cabinet pull sizes?
There’s no “rule”, it’s a matter of looking at as many kitchens as possible and figuring out the look you prefer. I also used a variety of sized pulls on drawers of different widths, and used Restoration Hardware.
What size pulls for 24 inch drawers?
Cabinet doors 24-36 inches tall are best adorned with pulls 7-12 inches long, while cabinets taller than 36 inches such as pantries, built-in appliances and pullouts should be accompanied by pulls longer than 12 inches.
What is the proper placement for cabinet knobs?
Cabinet knobs are placed opposite of door hinges. On wall cabinets, knobs are usually placed 2-1/2” to 3” from the bottom corner of the door. On base cabinets, they are placed 2-1/2” to 3” from the upper corner of the door. If your drawer is 24” or wider, you may choose to place a second knob.
Where should Pulls be placed on cabinets?
Pulls. Pulls are another versatile option that can be installed on both cabinets and drawers. For both upper and lower cabinets, the pulls should be installed vertically 2 ½ – 3 inches in from the corner of the door. For drawers, they should be installed horizontally in the center of the door.
Where do you put cup pulls on drawers?
Cup Pulls: Cup pulls are only ever used on drawers, and I like to center them in the middle of the drawer slab. If you have a 5 piece drawer (top and bottom rails, inside panel, and side rails) you want to make sure the hardware itself will fit (centered) in the middle panel before purchasing and installing.
Can you mix pulls and knobs on cabinets?
Yes. You can mix knobs and pulls. It’s recommended to use pulls for cabinets that are higher up and knobs for lower style cabinets. Lower drawers that slide are typically fitted with a pull handle.
Where do cup pulls go on Shaker cabinets?
Center of the Stile: Knobs and pulls can be placed halfway up the stile of your Shaker door. Keep in mind you’ll want to be able to reach the handles, since they will be placed higher up along the stile. Just Above or Below the Corners: Place the knobs or pulls 2” to 3” from the lower or upper corner.
