Table of Contents
How do I choose a miter saw size?
Blade size is an important consideration in selecting a miter saw. The most common miter saw sizes are 8, 10 and 12 inches. Keep in mind that larger diameter blades can make longer cuts. Positive stops are factory set points that let you quickly make precise cuts on specific angles.
Will a 10-inch miter saw cut a 2×6?
The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees. The sliding action can cut even wider boards.
What size Mitre saw for baseboards?
Compound Miter Saws For precise cuts, a 6-inch baseboard needs to be laid flat in an 8-1/2 inch saw to slice off a partial degree. The larger 10- and 12-inch models allow the 6-inch board to rest upright against the miter fence.
Can 10-inch miter saw cut a 4×4?
It may surprise you to know that the answer in question to cutting 4×4 posts with a miter saw is a hard, YES! If you can give the blade more clearance, then it should be possible to get a clean single pass cut through a 4×4 post, even when utilizing a 10-inch blade.
Is a 12-inch miter saw overkill?
But if you’re not a millionaire, think carefully about what you expect to do with your miter saw. If you’ve never even thought about needing the extra capacity the 12-inch provides, save your money and get the 10-inch. Don’t buy more tool than you need – buy the right tool for the job.
How big of a board will a 12-inch miter saw cut?
Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights. This larger saw can cut a maximum thickness of 3 1/2 inches, enough to cut through four-by-fours.
Does miter saw Size Matter?
If you’re working with regular baseboard molding, nothing industrial in terms of size, then a 10” miter saw should be more than enough. It can easily achieve a precise and clean 6” cut with a good blade.
How wide can a 7 1 4 miter saw cut?
The RYOBI 7-1/4 in. Sliding Miter Saw is a new edition to the miter family. It can make angled cuts up to 45° on boards all the way up to 6 in. wide, and has a max RPM of 5,350.
Can a 10 inch miter saw cut a 6X6?
A miter saw with a 10-inch blade installed can cut a 6X6 lumber piece, only it cannot do so with one single pass. To do this cut with a ten-inch blade you’ll need to follow several steps to complete your cut.
Can a 12 inch miter saw cut a 4×6?
Yes! A 12” miter saw can easily cut a 4 x 6 lumber. A 12 inch miter saw clearly has a bigger blade and has the capability to cut 4×6 lumber in a single pass.
Can a miter saw cut a 2×10?
Miter Saw Limitations The biggest drawback of a miter saw is that the smaller (and cheaper) sizes can’t cut completely through wide material, such as 2×10 or 2×12 boards, in one pass. Well, a sliding miter saw can make these cuts, but you’ll spend twice as much for one.
Can a 7 1 4 miter saw cut a 4×4?
No not with one cut. You would have to turn the 4×4 over. Blade is a 7 1/4″ diameter, same as a hand held circular saw.
What is a 7 1 4 miter saw used for?
Ideal for moulding and framing cuts, this Kobalt 9-amp sliding compound miter saw delivers 5,000-RPM of power. Positive miter and bevel stops provide accurate placement of most-used angles. The tall aluminum fence provides plenty of support, while a clamp stabilizes the material during miter, bevel and compound cuts.
What is the difference between a single and double bevel miter saw?
What’s the Difference Between a Single Bevel and Double Bevel Miter Saw? A single bevel miter saw can only tilt in one direction (either left or right). A dual bevel miter saw can tilt in both directions.
Can you put a 12 inch blade on a 10 inch table saw?
No. A 10 inch table saw is just big enough to accept a 10 in blade. 12 inch blades are too big to fit a 10 inch table saw.
What saw will cut a 4×4?
A circular saw is one of the best means of cutting a 4×4 post. Most people own a circular saw, its portability makes it easy to cut 4x4s from the ground, and they can make precision cuts by using a relatively simple trick.
Do you need a table for a miter saw?
Technically, you don’t need a stand to use a miter saw. You can use your saw on a table or any other flat surface you can find. After all, one of the best features of a miter saw is that it is portable and designed to go with you on a trip to the job site or wherever else you need it.
What is a 10-inch miter saw good for?
Common Uses for a 10-Inch Miter Saw Perfectly angled miter cuts. More complex bevel and compound angle cuts. Cutting plastic and metal pipes to length. Precise repeated cuts.
Can you put a 10 blade on a 12 Mitre saw?
Yes, as the max size on on a Miter Saw that was sold with a 12 in blade should accommodate a 10 in blade !.
