Table of Contents
Choose a pump that is at least one and one-half times the head height for optimal performance. For example, if your fountain is 30 inches tall, find a pump with a maximum lift of 45 inches or more.
What size pump do I need for a small water feature?
It is important to calculate the capacity of your pond, however, as a guide, for small ponds solely to run a fountain, a 700 – 1000 litre per hour pump is recommended.
What is the best pump for a water feature?
Best Fountain & Waterfall Pumps Review 2022 (Most Efficient Models) 1) TetraPond Feature Pump Review. 2) Laguna Powerjet Feature Pump Review. 3) TotalPond Feature Pump Review. Blagdon Mini Feature Pump Review. All Pond Solutions Feature Pump Review.
How do I choose a water feature pump?
If you have a 7000-litre fountain, you need a pump that can comfortably circulate 7000 litres of water in one hour. So, to determine what flow rate you need, simply divide the total water capacity of your pond by 60. For example: With a 7000 litre fountain, simply divide 7000 by 60 = 116.6.
How do I choose a pump size?
Before you can select a pump that will fit your needs, you must know four things: 1) the total head or pressure against which it must operate, 2) the desired flow rate, 3) the suction lift, and 4) characteristics of the fluid.
How do I know what size waterfall pump I need?
To determine the GPH/GPM needed for your waterfall or stream – multiply the width in feet x 30 GPM. Example: To build an “average” waterfall 3′ wide and 10′ high above the pond – multiply 3′ (width) x 30 GPM which equals 90 GPM or 5,400 GPH at 10 feet of head.
Can you use a sump pump for a fountain?
Yes, sump pumps can be used to drain ponds with fountains. Make sure that the fountain is turned off and the drainage pump is setup far away from the fountain. If part of the fountain enters the sump pump motor is could permanently damage both the sump pump and the fountain.
What type of pump is used for waterfalls?
Types of Pond Pumps, Waterfall Pumps, and Fountain Pumps Pond Pumps are re-circulating and most often Submersible Pumps that power Waterfalls, Water Fountains and in garden ponds.
What is a good fountain pump?
BEST OVERALL: VIVOSUN 4500GPH Submersible Water Pump. BEST BANG FOR THE BUCK: Knifel Submersible Pump. UPGRADE PICK: Tetra Pond Debris-Handling Pump. BEST FOR SMALL PONDS: Aquagarden Water Pump for Ponds. BEST FOR LARGER PONDS: TotalPond 2000 GPH Waterfall Pump.
How big a pond pump do I need?
It is recommended that pond water is circulated at least once per hour. For example, if you have a 500-gallon pond, you need a pump that runs 500 GPH at the height of the discharge. This is true if it also has a skimmer or waterfall.
How many GPH do you need for a fountain?
The rule of thumb, depending on just how much water you want coming out of the fountain, is 100 GPH per one inch diameter of fountain outlet.
What size pump do I need to lift water 20 feet?
Example – Horsepower Required to Pump Water Power Required to Pump Water (hp) Volume Flow (gpm) Height (ft) 10 0.0126 0.0505 15 0.0189 0.0758 20 0.0253 0.101.
How far can water be lifted by a pump?
Specific gravity suggests that water can be pumped from less than or equal to 26 feet down when operating at sea level, which is to say that when you’re at sea level with a water pump, you can only expect your pump to have a maximum suction lift of 26 feet or less.
Can a pond pump be too powerful?
A pump that is too big will churn the water more violently than necessary which can cause injury to any plants or fish that you may have in the pond. The water only needs to be circulated, not heaved.
What size pump do I need to pump water uphill?
A 1/2 Hp pump should be able to push water up hill 40 ft without problems.
Can I use a sump pump for a pond fountain?
Sump pumps are widely used on pond fountains because they are inexpensive. Most sump pumps are intended to operate only for the period of time necessary to pump water out of a flooded area like a basement.
Can I use a sump pump as a well pump?
A sump pump is designed to remove water from the sump basin of your home’s basement. However, in some cases, you can use these pumps for other purposes. In most cases, if your sump pump is compatible to use with a residential fountain, pond or other water feature, its box will note that fact.
How big of a water pump do I need?
Pumps are rated in GPM (gallons per minute). A typical 3- to 4-bedroom home requires 8-12 GPM. When determining your home water needs, add one GPM for every water fixture in your home.
What is the difference between a pond pump and a waterfall pump?
Direct Drive Pond Pumps are stronger pumps usually referred to as a Waterfall Pump and best used for taller waterfalls and higher head lift situations. Direct Drive pumps usually take a little more energy since they are more powerful and since they have more parts that can wear down usually have a shorter warranty.
Do I leave my pond pump on all the time?
A pond pump and a filter are necessary to maintain pond health. A pond’s pump should run 24 hours each day to ensure the pond’s water circulates through the filter to keep the water clear.
