Table of Contents
Waterfalls. Choose a waterfall pump to match the height and width of your waterfall. The rule of thumb is for every 1 in. of spillway width, you need 100 gallons per hour flow to achieve a “sheet” look.
How do I know what size waterfall pump I need?
To determine the GPH/GPM needed for your waterfall or stream – multiply the width in feet x 30 GPM. Example: To build an “average” waterfall 3′ wide and 10′ high above the pond – multiply 3′ (width) x 30 GPM which equals 90 GPM or 5,400 GPH at 10 feet of head.
What water pump do I need for waterfall?
Flow Rate: The average amount of water moving over a waterfall is 1,500 GPH for every 1′ of width. Therefore, a waterfall that is 2′ wide would need a 3,000 GPH pump. If you are looking for a heavier flow, calculate your flow using 2,000 GPH per foot.
What size pump do I need for my water feature?
Choose a pump that is at least one and one-half times the head height for optimal performance. For example, if your fountain is 30 inches tall, find a pump with a maximum lift of 45 inches or more.
How do I choose a waterfall pump?
A good rule of thumb is to choose a Waterfall Pump that moves 100 gallons per hour for every inch of Waterfall width. Select a less powerful Pond Pump for gentle waterfalls and for aggressive waterfalls use a more powerful pond pump.
Can I use a sump pump for my waterfall?
A sump pump might seem like a good idea for pumping water but a sump pump is not the best choice. They are too large, too powerful and too expensive to use in a small outdoor waterfall.
What size pump do I need for a 1000 Litre pond?
Water Circulation Factors If your pond has a pressurized filter, you ideally want to turn the water approximately once every two hours. For example, if you have a 1,000-gallon pond, then you need a pond pump rated at a minimum of 500 GPH.
What is the difference between a pond pump and a waterfall pump?
Direct Drive Pond Pumps are stronger pumps usually referred to as a Waterfall Pump and best used for taller waterfalls and higher head lift situations. Direct Drive pumps usually take a little more energy since they are more powerful and since they have more parts that can wear down usually have a shorter warranty.
How do you determine what size pump you need?
Use the pump flowrate calculation: Divide the container volume by the length of time it took to fill up to get the flow rate. 5 gallons / 1 minute = 5 gallons per minute. 5 gallons /30 seconds (0.5 minutes) = 10 gallons per minute.
What is the best pump for a water feature?
The Best Small Fountain Pump For A DIY Garden Fountain Our Top Pick: Homasy 400GPH Submersible Pump. KEDSUM 550GPH Submersible Pump. Homasy 80 GPH Submersible Water Pump. VicTsing 80 GPH Submersible Water Pump. Intsun 220 GPH Submersible Water Pump.
What size pump do I need for a 300 gallon pond?
Water feature volume. To figure out the volume of a pond or fountain in gallons, multiply its length by width by average depth (all in feet) by 7.5. For a 300-gallon water feature of a type (explained below) that requires water circulation every two hours, you’d look for a pump with a flow rate of 150 GPH.
What size pump do I need to pump water uphill?
A 1/2 Hp pump should be able to push water up hill 40 ft without problems.
Can a pond pump be too big?
A pond pump can be too big for the size of pond, causing excess water loss, increased energy usage, an uncomfortable noise level, and an unsuitable environment for plants or fish. Careful calculation of your pump needs before purchase will help to avoid future difficulties.
How do I know what size pond pump I need?
A good rule of thumb is that pumps should be able to pump out about half the pond volume every hour. For example, a pump that moves 500 gallons per hour would be appropriate for a 1,000 gallon pond.
What size pond pump do I need for my pond?
Pumps designed for garden ponds are sized by gallons per hour (GPH) output at one foot of lift or height. It is recommended that the entire volume of water in a garden pond be pumped per one to two hours. What this means is that a pond holding 500-gallons of water should have at least a 500 Gallon Per Hour pump.
Can I use a submersible pump for a fountain?
A submersible pump needs to operate while submersed in the water. If it is brought up above the water while in operation, the pump will burn out and stop working. This type of pump may be used in a fountain, a pond or a variety of water features that require a pump to push water from one point to another.
Can I use a sump pump for a pond fountain?
Sump pumps are widely used on pond fountains because they are inexpensive. Most sump pumps are intended to operate only for the period of time necessary to pump water out of a flooded area like a basement. Sump pumps will give an acceptable lifespan when used in a lined pond filled with well water.
Can I use a sump pump as a well pump?
A sump pump is designed to remove water from the sump basin of your home’s basement. However, in some cases, you can use these pumps for other purposes. In most cases, if your sump pump is compatible to use with a residential fountain, pond or other water feature, its box will note that fact.
