QA

Question: What Will Be The Maximum Clearance

Maximum and minimum clearance The maximum clearance of a fit is the difference between the upper bound of the orifice diameter and the lower bound of the shaft diameter. The minimum clearance meanwhile is the difference between the lower bound of the orifice diameter and the upper bound of the shaft diameter.

What is the maximum and minimum limit of hole?

Maximum clearance: The positive difference between the maximum size of a hole and the minimum size of a shaft.

What is maximum material limit?

MMC is the condition of a feature which contains the maximum amount of material, that is, the smallest hole or largest pin, within the stated limits of size. LMC is the condition in which there is the least amount of material, the largest hole or smallest pin, within the stated limits of size.

What is clearance fit?

Clearance fit is an air space or clearance which exists between the shaft and holes. Such clearance fits give loose joints. The clearance fit has to be joined with other fits so that the clearance fit can have its space.

What does clearance mean in dimensions?

Stated simply, CLEARANCE is the distance between the adjacent surfaces of mating parts (how much the mating parts CLEAR each other), while TOLERANCE is the allowable variation of a dimension from its nominal (desired) value ( the amount of error one will TOLERATE ).

What is go limit?

Explanation: ‘Go limit’ deals with upper limit of shaft and lower limit of hole and refers to the maximum material condition. ‘No-go’ limits deals with lower limit of shaft and upper limit of hole and refers to the minimum material condition.

What is basic size limits and tolerance?

5. Basic Size: The term basic size refers to the size from which the limits of size are derived by the application of tolerance (i.e. upper and lower deviation). The basic size or nominal size of a part is often the same and it is termed as zero line.

What is Max material?

Definition: Maximum Material Condition or for short, MMC, is a feature of size symbol that describes the condition of a feature or part where the maximum amount of material (volume/size) exists within its dimensional tolerance.

What is material limit?

Least Material Condition (LMC) is that condition of a part or feature which contains the minimum amount of material, e.g. maximum size hole or a minimum size shaft. Circumstances do arise where, for example, a designer would want to limit the minimum wall thickness between a hole and the side of a component.

Under what conditions is Rule #1 not applicable?

Exceptions to Rule #1 Rule #1 does not apply to a FOS on a part subject to free-state variation in the unrestrained condition. In simple terms, Rule #1 does not apply to flexible parts that are not restrained. Rule #1 does not apply to stock sizes, such as bar stock, tubing, sheet metal, or structural shapes.

What are the 3 types of fits?

ISO and ANSI both group fits into three categories: clearance, location or transition, and interference. Within each category are several codes to define the size limits of the hole or shaft – the combination of which determines the type of fit.

Where are clearance fits used?

Examples of clearance fit are door hinges, wheel, and axle, shaft and bearing, etc. used in the assembly of parts. It is used between those mating parts where no precision is required. It provides minimum allowance and is used on loose pulleys, agricultural machineries, etc.

What is maximum interference?

Maximum interference is arithmetical difference between the minimum size of the hole and the maximum size of the shaft before assembly. Minimum interference is the difference between the maximum size of the hole and the minimum size of the shaft.

What is the minimum clearance provided for the 132KV line from the ground?

So, as per logic, the ground clearance of 132KV bottom conductor would be, 5.2 + 0.9 = 6.1 meter. The minimum clearance of 66KV transmission line is also taken as 6.1 meters. Actually, in any case, the ground clearance should not be less than 6.1 meters across a street.

What is the basic size?

: a sheet size used as a standard in the paper industry (such as 17 × 22 in. for ledger, bond, and writing papers).

What are CMM precious moments?

What precise movement does CMM have? Explanation: Co-ordinate measuring machines are useful for three dimensional measurements. These machines have precise movements in x,y and z coordinates which can be easily measured and controlled.

What is the use of no go gorgeous?

Go – No Go gauges are manual mechanical measuring tools used in production lines to guarantee the machining has taken place and it has been performed correctly. They differ from each other based on the type of surface check being performed; for example geometry and/or dimension.

What is meant by roughness?

Definitions of roughness. a texture of a surface or edge that is not smooth but is irregular and uneven. synonyms: raggedness. Antonyms: smoothness. a texture without roughness; smooth to the touch.

How is tolerance calculated?

The %URV criterion is the upper range value divided by 100. If the upper input range value is used, the value must be converted to output units before the tolerance is calculated. The converted tolerance is then added to or subtracted from the desired output value to determine the range limits.

What is tolerance chart?

A tolerance chart is a graphical representation of a process plan and a manual procedure for controlling tolerance stackup when the machining of a component involves interdependent tolerance chains. A special path tracing algorithm is used to identify tolerance chains from this graph.

What does the M mean in GD&T?

Maximum Material Condition is one of three features of size callouts in GD&T. The other two are Least Material Condition and Regardless of Feature Size. All of these specify the condition that the part or feature must be in to apply the specified geometric tolerance.

What is minimum metal condition?

[′min·ə·məm ′med·əl kən‚dish·ən] (design engineering) The condition corresponding to the removal of the greatest amount of material permissible in a machined part.

Why do we use MMC and LMC?

Maximum material condition (MMC) is used to indicate tolerance for mating parts such as a shaft and its housing. Least material condition (LMC) is used to indicate the strength of holes near edges as well as the thickness of pipes.