Table of Contents
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How do you restart a furnace?
How to Reboot a Furnace Change the Filter. Before you do anything, check the furnace filter. Check the Pilot Light. If the pilot light is off, your furnace can’t get the spark necessary to light the boilers. Turn the Furnace Off and Back On Again. Call a Certified HVAC Professional.
Where is my furnace blower motor reset?
How to Find and Reset your Furnace Motor Blower Step 1: Turn off the power to the furnace. Step 2: Remove the blower compartment cover. Step 3: Make sure the blower is completely cooled off. Step 4: Locate the reset button. Step 5: Press the button in (assuming that this is your issue and that the button has popped).
Does every furnace have a reset button?
All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.
Should I hit the reset button on my furnace?
The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.
How long does it take for furnace to reset?
Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too. Never touch the breaker with wet hands and use only one hand to do it.
How do you manually reset a furnace?
Follow these simple steps: First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. If the button is popped up, press it down. Return the cover to the blower compartment and turn the power on.
What does blower motor reset button look like?
Examine the exposed components in the furnace cabinet to locate the blower motor; look for a small silver box positioned toward the top of the cabinet. Mounted just above this box you should see a small round component with a raised red or white button at the center; this is the blower reset switch.
How do I reset my furnace lockout?
Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.
How many times can I hit the reset button on my furnace?
Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.
Why is my furnace reset button not working?
Obstructed airflow: Sometimes the reset button gets tripped because the furnace isn’t receiving enough airflow. Dirty flame sensor rod: Every now and then, the flame sensor rod gets dirty and shuts the furnace off. Make sure you wipe it off regularly. Low fuel: Low fuel is also a common cause of burner failure.
Why is my furnace not heating?
Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won’t warm up. If the blower is running but no heat is coming out, replace the filter.
Why is my furnace not running?
Ensure your furnace filters are clean: Your furnace won’t start up if it does not get enough airflow. Check your pilot light: If you have a gas furnace and gas supply is stopped your pilot light will go out. Check your blower motor: If the blower motor is not working then your furnace won’t pump out warm air.
Why is my furnace running but not blowing air?
Check Your Furnace Air Filter Next, check your heater’s air filter, as this can cause a furnace to stop blowing air. Your filter could be so saturated with dust and debris. In that case, even though the furnace is actually blowing air, your clogged filter is blocking it from making it into your ducts.
Where is the furnace switch located?
Most building codes require a furnace switch or “disconnecting means” within sight of the furnace itself. It’s usually mounted on the side of the furnace or a wall nearby.
How do I turn my furnace on?
Set the thermostat. The thermostat of your furnace should now have power. Select the “Heat” setting on the thermostat, then set the temperature to your preference. When the temperature drops below the thermostat setting, the furnace will turn on and heat your home.
How do you reset a furnace after overheating?
How to Reset Your Furnace Turn down the thermostat to its lowest setting. At the circuit breaker, turn off the power to the furnace. If this is a gas furnace, turn off the gas supply at the valve for the main gas pipe, but leave the pilot’s gas supply on. If the pilot light was out, light a match to relight it.
