QA

Where Is The Thermocouple On My Rv Furnace

Inside the main burner there will be an assembly containing both the thermocouple and the pilot flame burner. The thermocouple is cylindrical and sits in the pilot flame; hence it will be the topmost of the pilot burner/thermocouple combination.

Does an RV furnace have a thermocouple?

One other RV heater troubleshooting tip is: check the thermocouple. The thermocouple is a bimetallic sensor whose electrical resistance changes with temperature. This change in resistance is detected by the control system, to ensure there is a flame before it opens the main gas valve.

How do you test an RV thermocouple?

Place one test lead on the side of the thermocouple and the other to the end that screws into the gas valve. If the thermocouple has proper continuity, a small resistance reading should be visible on the multimeter. Many multimeters also indicate continuity with an audio alert.

What is a RV thermocouple?

The thermocouple is an electo-mechanical safety device that senses if the pilot flame in an RV appliance is present. When lighting the pilot flame, allow the thermocouple to heat up for 30 seconds or so before releasing the valve button.

Is there a reset button on a RV furnace?

Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor.

Why Is My RV furnace not blowing hot air?

If there is no fan noise coming from your RV furnace, it may be dead because of a lack of power. However, you won’t have much to go on since there aren’t any components working on the furnace for you to diagnose. You will need to check the battery, check the circuit breaker, and check the fuse for the fan.

Can I replace a thermocouple myself?

1 cause of pilot lights that won’t stay lit is a worn-out thermocouple. It’s easy to replace and a new one costs $5 to $10. Then detach the thermocouple from the burner and take it with you to the home center or hardware store to ensure you buy the right replacement.

How do I know if my thermocouple is bad on my furnace?

If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.

Do all furnaces have a thermocouple?

Most gas furnaces use either a flame sensor or a thermocouple, sometimes referred to as a “thermal coupler.” Both are safety devices that sense the presence of a flame and control the flow of gas to the appliance accordingly.

Can you clean a thermocouple?

Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up.

How do you bypass a thermocouple?

To bypass the thermocouple: Move the tilts switch wire aside. Remove your thermocouple from the heater using an 8mm wrench. Pull the valve housing aside using your 13mm socket wrench. Remove the valve using your pliers. Put your thermocouple back into position.

How do you fix a thermocouple on a propane heater?

If the thermocouple is too far from the flame, this can cause the pilot to go out and shut down the propane heater; you can fix this easily by moving the thermocouple closer to the flame. The thermocouple could also be worn out, in which case it needs to be replaced.

How do you test a Dometic thermocouple?

Hold the ignition to bypass the thermocouple, and then give the heat sensor roughly 30 seconds to heat up. The flame should be steady and mostly blue, and the thermocouple should be about half an inch inside the flame.

What would cause a furnace not to kick on?

The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up. If the sensor or ignitor is dirty, it will need to be cleaned.

How do I reset my furnace lockout?

Most modern gas furnaces can be reset by turning off the power, waiting around 20 seconds, then switching the power back on. Other furnace models may exit lockout after 1-2 hours and attempt to power on again. If your furnace has a pilot light, you may need to relight it following the manufacturer’s instructions.

Why Is My RV furnace only blowing cold air?

Sail Switch This is a very common issue with RV furnaces not fully igniting, and as a result, just blowing cold air. This switch can become blocked with pet fur, dust, and debris from the RV sitting, or from being collected and blown around by the fan itself.

What do I do if my furnace is blowing cold air?

How To Troubleshoot Furnace Blowing Cold Air Step 1: Check Thermostat Setting. First and most importantly, make sure your thermostat is set to Heating Mode. Step 2: Evaluate and Adjust Your Vents: Step 3: Assess Furnace Filters and Replace Filters If They Are Dirty. Step 4: Call An HVAC Pro.

How much does it cost to replace a furnace thermocouple?

Cost to Replace a Thermocouple on a Furnace Replacing a thermocouple costs $150 to $250, mostly due to labor time. On older models without an ignitor, it checks to make sure your pilot light is lit. If it’s not, it’ll shut the gas off.

How much does a thermocouple cost?

It costs $150 to $250 to replace a thermocouple. It checks to make sure the pilot light is on.