QA

Quick Answer: Why Is My Electric Pool Heater Not Working

The most common cause is flow, a dirty basket, or clogged or dirty filter. A pool heater is an “open boiler” system, meaning the heater is cooled by the water flowing through the heater. All pool heaters have a pressure switch or flow switch that measures the flow rate of water pumped into the heater.

How do you troubleshoot an electric pool heater?

Low Flow or Inadequate Heating Clean the filter and set the temperature switch to the ON position at a high enough setting that the heater turns on. Reset the timer to allow the heater to run for a longer period. Check the systems valves as well to make sure that they are turned to go through the heater.

Why is my pool heater not heating my pool?

The most common issue when a swimming pool heater won’t heat is also the simplest one, a dirty swimming pool filter. A dirty pool filter or pump basket will restrict the water flow, so always ensure that everything is clean and all valves are open.

How do I reset my pool heater?

Reset the circuit breaker for the pool heater. Put the system in standby using the control panel (typically accomplished by pressing and holding the Up & Down buttons) Check for an error code (if you see a code like bD or HF this could indicate a gas problem and your system will not reset until the problem is resolved).

How long do pool heaters last?

You can expect a gas or heat pump pool heater to last 8 to 11 years, with an average of 10 years. Regular usage and maintenance is key to a longer lifespan.

Why is my heat pump not heating?

Low refrigerant charge – If your system is low on refrigerant charge, it won’t be able to keep up with either heating or cooling demand. Another sign of low refrigerant charge is a frozen coil. Bad reversing valve – If you have a heat pump not heating, but it works in cooling mode, you might have a bad reversing valve.

Why does my pool heater not ignite?

If the pilot won’t light, the gas pressure could be low, the air supply may be poor, or the heater may not be venting properly. Check the gas pressure, and adjust it if necessary. Then check all the vents to make sure they’re not blocked. If any of them are, simply remove the blockage, and try lighting the pilot again.

Why will my heater not turn on?

Check the Pilot Light – A dirty or faulty pilot light is one of the main reasons a gas furnace won’t start. Make Sure Natural Gas Is Flowing into the Furnace – If your furnace won’t start, it may be because the unit isn’t getting any fuel. Simply check the gas control valve to ensure it’s in the “On” position.

Do pool heaters have pilot lights?

Pilot Light Keeps Going Out Direct sprinklers and rain spouts away from the heater or use a cover that will keep rain and snow out. You may need a pool heater wind stack to prevent wind from reaching the pilot light.

What temperature should pool heater be set at?

What Is the Perfect Temperature? Pool water temperatures typically run between 78 and 82 degrees. Any cooler than 78 and you will feel chilled when you exit the pool. Any warmer than 82 and the pool will feel like bath water.

Why is my Raypak pool heater not working?

Check the Power: If your Raypak pool heater isn’t working at all, the problem could be something as simple as a lack of power. Go make sure there aren’t any tripped circuit breakers in the fuse box, then check that the unit’s time clock is set to the “On” position.

Should I leave my pool heat pump on all the time?

Unlike gas heaters, heat pumps are most efficient when they are run for long periods of time and when they are run often. If you only run your heat pump when you use your swimming pool, your heat pump will have to raise your water temperature by as much as 20°F (11°C) every time you use your swimming pool.

Why is my Hayward pool heater not working?

If the heater has not been fired in over a week, chances are there is a blockage in the burners or orifices that is preventing the gas from escaping the burner and reaching the spark. Other causes of this problem are: (1) Bad ignitor. (2) Bad gas valve.

How do you turn on a titanium pool heater?

To turn heater on: Press & release the set button four times until “OFF” appears. Press down button twice then “ON” appears. Heater is now on. Pool & Spa lights will illuminate beside display indicating heater is on.

Why does my pool heater says Flo?

The FLO code is indicating that the filter pump has stopped the flow of water to your heat pump. The heat pump cannot heat without water flow so it will turn itself off until the filter pump timer turns back on giving the heat pump the water flow it needs.

Can I leave my pool heater on all night?

When asking can you leave pool heater on overnight, the answer is definitely no if you have no swimming pool cover. So unless you have money to burn, it’s best not to run your heater at night on an uncovered swimming pool.

How much does a heater for a pool cost?

Between setup and operating costs, a pool heater costs between $300 and $5,000, with the average cost around $2,000.

Is it worth getting a pool heater?

Pool heaters have the potential to be an incredibly worthwhile investment if a family wants to utilize its new pool year ’round, or even just well into school starting in the fall. However, if a family only plans to use a pool in the hot days of summer, a pool heater is not as necessary.

How long does it take for pool heaters to work?

Overall, a heat pump usually requires between 24 and 72 hours to heat a swimming pool by 20°F (11°C) and between 45 and 60 minutes to heat a spa by 20°F (11°C).