Table of Contents
Why must slip be present for motor Action?
Slip of induction motor plays an important role in the operation of the induction motor. The torque produced by the induction motor is directly proportional to induction motor slip. At no-load induction motor requires small torque to meet with the frictional, iron and other losses, therefore slip is small.
Why is slip necessary in an induction motor?
In actual operation, rotor speed always lags the magnetic field’s speed, allowing the rotor bars to cut magnetic lines of force and produce useful torque. This speed difference is called slip speed. Slip also increases with load and it is necessary for producing of torque.
What is slip in 3 phase induction?
Slip in Induction Motor is the relative speed between the rotating magnetic flux and rotor expressed in terms of per unit synchronous speed. It is a dimensionless quantity. The value of slip in induction motor is can never be zero.
Why there is no slip in synchronous motor?
Because the rotor turns at the same speed as synchronous speed (speed of the rotating magnetic field), there is no slip. The speed of rotation of the motor is constant in a synchronous motor, and does not vary with load, as in an induction motor.
What is full load slip?
The slip corresponding to full load speed of th motor is called full load slip. Example 1 : A 4 pole, 3 phase induction motor is supplied from Hz supply. Determine its synchronous speed. On full load, its speed is observed to be 1410 r.p.m. calculate its full load slip.
What is the difference between rotor speed and synchronous speed?
Induction motor with squirrel cage rotor has two different speeds. The synchronous speed refers to the stator rotating magnetic field, which depends on the number of poles and frequency. The other speed is the rotor’s. The rotor speed will be always slower than the stator speed, we call it slip.
What is normal slip of an induction motor?
Because of this speed difference, the motor rotates at a speed slightly slower than the synchronous speed. Slip is normally expressed in percentage. Slip of a power induction motor is 2 to 3% when the motor is operated under the rated load.
What is the importance of slip in 3 phase induction motor?
Slip creates a relative speed between the RMF and rotor. That keeps a torque continuously acting on it when the motor is running. So what would happen if slip becomes zero? Bcoz there will be no relative speed between RMF and rotor, and which will stop inducing rotor current.
Can slip be negative?
If the rotor of an induction machine rotates above synchronous speed, slip is negative, as are torque, mechanical output power and air gap power. i.e. the machine is operating as a generator. Rotational losses are 2450W.
What is slip speed?
The speed at which the induction motor work is known as the slip speed. The difference between the synchronous speed and the actual speed of the rotor is known as the slip speed. In other words, the slip speed shows the relative speed of the rotor concerning the speed of the field.
How is slip in motor calculated?
What is Slip in an Induction Motor? Definition: In Induction Motor, a slip is a speed among the rotary magnetic flux as well as rotor expressed in terms of for every unit synchronous speed. It can be measured in dimensionless & the value of this motor cannot be zero. S = (Ns – Nr) / Ns. Slip = (Ns-Nr/Ns)*100.
What are merits and demerits of slip ring induction motor?
Speed regulation is poor when operated with external resistances in rotor circuit. Efficiency and power factor of slip ring motor is lower compared to squirrel cage induction motor. Lower power factor at the light loads. Sensitivity to fluctuations in supply voltage.
What is synchronous speed and slip?
Slip is the difference between the synchronous speed of a motor and its actual speed. Mathematically it is determined by. Slip = Synchronous Speed − Actual Speed. Using the example above for synchronous speed of a motor with four poles operating at 60 hertz, the value was calculated to be 1800 RPM.
How can we increase the speed of synchronous motor?
However, with the invention of solid-state devices, the frequency of the current fed to the synchronous motor can be varied. We can control the speed of the synchronous motor by changing the frequency of the supply to the motor.
What is synchronous speed?
The synchronous speed is the speed of the revolution of the magnetic field in the stator winding of the motor. It is the speed at which the electromotive force is produced by the alternating machine. The Synchronous Speed is given by the relation shown below.
What is no load slip?
The speed is assumed to be synchronized. The synchronous speed can be achieved by taking slip = 0 which creates infinite impedance in the rotor branch. Rotor copper loss at no load is very less that its value is negligible. Small current is required to produce adequate torque.
What is value of slip at no load?
At no-load condition, the rotor speed is almost equal to the synchronous speed. e.g A 4 pole, 60 Hz induction motor at no load turning at ηr = 1790 RPM will have slip = (1800 – 1790)/(1800) = 0.55%Mar 9, 2020.
What is slip torque?
The torque slip curve for an induction motor gives us the information about the variation of torque with the slip. The slip is defined as the ratio of difference of synchronous speed and actual rotor speed to the synchronous speed of the machine.
Can induction motor run at synchronous speed?
So, theoretically, the Induction motor can never run at synchronous speed. But due to the reduction of speed, again lag influx will be achieved, and the motor will continue to move at this speed due to flux difference between rotor and stator. In short, an induction motor cannot run at induction speed.
What is the relationship between frequency and synchronous speed?
The synchronous speed of the motor can be changed by changing the number of poles or by changing the frequency. The machine which runs at synchronous speed is called synchronous machine.Synchronous speed Formula. No. of Poles Frequency (50 Hz) Frequency(60 Hz) 4 1500 1800 6 1000 1200 8 750 900 10 600 720.
Why can the synchronous speed never be the same as the rotor speed?
When rotor speed equals synchronous speed mean s = 0 or no induced EMF in rotor conductor or no torque. This is the reason for rotor rotates lesser speed than synchronous speed.
