QA

Quick Answer: How Deep Can You Make A Cabinet Drawer

How deep can I make a drawer?

Drawer depth or height is not critical, but the most common difference between the drawer and the opening is 3/4 inch. For example, if the opening measures 4 inches vertically, the drawer should be built 3 1/4 inches. This allows 1/4 inch at the bottom where the slide is attached, and 1/2 inch at the top for clearance.

How deep is a cabinet drawer?

The standard depth is 12 inches, but you can find other sizes, from 15 to 36 inches.

How deep should drawer be?

Allow at least 1/4” of clearance above and below the drawer, giving you a height of 5-1/2” (6” minus 1/4” at top and 1/4” at bottom). Your drawer box should be 17” wide, 5-1/2” tall and 22” deep.

How far does a cabinet drawer pull out?

Using a pull that is approximately 1/3 the length of the drawer is a good rule of thumb. For modern cabinetry, you can use extra long pulls that span nearly the entire width of each cabinet.

How thick are drawer slides?

Light duty slides might be as thin as 1/2″, while heavy duty slides may be over 3/4″ thick. Face frame cabinet slides are easier to install using the specific, optional, face frame brackets. Length sizing is usually simplified by checking manufacturer’s charts, where the drawer size and cabinet depth are both stated.

How deep should a drawer be for pots and pans?

Other Types Of Drawers And Their Sizes Pots and Pan Drawers are typically about 8-10″ high. We prefer them to be about 30″ in width if your kitchen allows it and 36″ is even better. Their depth will be dependant upon the depth of your base cabinet, which is typically 24″, 30″, or 36″ for standard cabinetry.

What are standard cabinet depths?

Standard kitchen cabinet heights include 12, 15, 18, 30, 36 and 42 inches tall; depth ranges from 12 to 18 inches. Typically installed 18 inches above countertops, 54 inches above floor and 24 inches above stove.

How deep should pan drawers be?

Plan your Drawer Layout The most common layout for drawers is 2 boxes at 10” high and one at 4” high. You may find a two-drawer stack works best with two extra deep drawers. If you want to store a lot of baking sheets or utensils you might want to consider one 10” deep drawer with three 4” deep drawers above it.

How thick should a drawer bottom be?

The sides and back of the drawer should be 1⁄2” or 5⁄8” thick. Use thinner stock for smaller drawers and thicker stock for big ones. The bottom is usually 1⁄4“-thick plywood for small drawers or 1⁄2“-thick material for bigger drawers, or drawers that will hold heavy objects.

Is a 36 inch drawer too big?

A deep, wide drawer does have a limit in size. You just can’t do a wide drawer at 36” wide or more, because it will sag over time, even with heavy duty glides. Homeowners might tend to weigh down that drawer with big, heavy items and you have to account for that happening somewhat.

How big is too big for a drawer?

The rule of thumb is 1.5 times the length of the drawer slide. If you have a standard depth kitchen cabinet then the normal length of drawer slide is 22”. If you multiply 22” x 1.5 = 33”. You can go wider, but the wider you go the more chance that the slide will not pull out as smoothly as you hope or expect.

What size pulls for 30 inch drawers?

Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter. Large Drawers that are 30” to 48″will require a pull that is longer than 8″ or a knob that is 1″ in diameter or greater. Using two pulls or knobs for a large drawer also works great.

Where should drawer pulls be placed?

Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.

What is the proper placement for cabinet handles?

Cabinet knobs are placed opposite of door hinges. On wall cabinets, knobs are usually placed 2-1/2” to 3” from the bottom corner of the door. On base cabinets, they are placed 2-1/2” to 3” from the upper corner of the door. If your drawer is 24” or wider, you may choose to place a second knob.

How thick are bottom mount drawer slides?

10″ Bottom-Mount Drawer Slide Kit, Steel Tracks, 1.2 mm Thick, 1-Pair, White Powder Coat Finish, 2-Pack.

Can drawer slides be shorter than drawer?

You should always use the longest slide possible for your application, without exceeding the drawer depth into the cabinet. The Height of a Drawer Slide is usually only a limiting factor, in the sense that you can’t install a slide that is taller than your drawer or pull-out.

What kind of wood is used for drawer boxes?

Poplar is a great all-around choice for drawer box construction. It is stable, durable, and much less expensive than most hardwoods. The color of poplar heartwood ranges from a creamy white to a yellowish tan or brown. It is very easy to work with and has straight, uniform grain.

How thick should Plywood be for drawers?

Plywood for most drawers is 1/4 inch thick but can be 1/2 inch thick on large drawers. You can find these materials in many different types of hardwood so that one or both of the outer veneers can match your drawer boxes and/or fronts.