Table of Contents
No. Celotex is not suitable directly below floor tiles. A screed is required to spread the load and prevent movement between the tiles.
Can you lay tile on insulation board?
Due to their waterproof properties, Warmup or Wedi insulation boards are perfect for insulating bathroom and wet room walls. As long as the joints of the boards have been sealed, wall tiles can be applied directly onto the insulation boards or over the heating system.
Can you tile onto kingspan?
I wouldn’t tile onto kingspan! Neither would I; given the bathroom environment, it could provide a very nice environment for all sorts of nasties!Aug 21, 2010
What goes on top floor insulation?
The damp proof membrane is placed over a layer of sand to prevent it being punctured by sharp stones. As it also serves as an airtightness membrane, it laps up the sides of the walls to link to the plaster or plasterboard. Insulation goes on top of this and around the edges, and concrete is poured on top of that.
Can you tile onto insulated plasterboard?
You can use a gypsum moisture resistant board, (where the board offers a protected core as well as lining). Finally a moisture resistant adhesive can be used; when applied ensure that the adhesive covers and protects the entire wall surface i.e. not just using a dot and dab method to fix tiles.
How do you install Celotex insulation boards?
Fitting the Celotex insulation Step two: Install Celotex insulation tightly between studs, pushing it up to plywood sheathing. For improved thermal performance, place the unprinted foil surface face against the air cavity within the studwork.
Do I need a Vapour control layer?
Do I need Vapour Control Layers for my floor? In ground floor applications such as concrete slabs and beam and block applications, a VCL is required on the warm side of the insulation. This will also help protect the insulation from wet screed or concrete.
Should you insulate under tiles?
Under-tile insulation is the perfect way to keep your tile floor warm. Topps Tiles stocks products from top brands, including Warmup insulation boards.
Can I screw through vapor barrier?
1 Answer. Typically, nothing is done. That puncture should be at a tight connection of drywall to stud, where airflow is impeded by the pressure of the screw holding the drywall and vapor barrier to the stud.
Can you lay concrete on Celotex?
Established Member. Standard foil backed celotex is suitable for having a concrete slab poured over it.
Is kingspan a Vapour barrier?
Composite products (such as Kingspan K118 Insulated Plasterboard) include integral moisture vapour control. As with any vapour control, workmanship is crucial. For example, taping and lapping joints for polythene, avoiding penetrations, and then sealing around any penetrations.
Can you put insulation under ceramic floor tiles?
Underfloor Heating World, Under tile and stone hard thermal insulation boards are designed for use directly under tiles and stone floors. When used under underfloor heating the board greatly increases the response rate and overall efficiency of all under floor heating systems.
How do you stick Celotex to floor?
Simply fix the Celotex floor insulation boards to the joists’ underside at 400mm centres, using galvanised clout nails and fix adequate fire protection board to the soffit. For improving acoustics of the space, you can install a layer of rock wool insulation (100mm thick) between the floor joists.
Do ceiling tiles have an R value?
Insulation Value of Ceiling Tiles Another great feature of insulated tiles below an attic is they can offer an R-3.5 protection against cold in the winter and heat in the summer. Properly sealed in the T-grid frame they offer an added protection in two forms: Insulation qualities of the tile.
Does Celotex require an air gap?
Established Member. The celotex and osb will act as a vapour barrier for the inside and the small air gap should suffice with the thin battens as mentioned for the “breather” bit. It’s not ideal but it’s only a shed and should last a while.
Can you use plasterboard in the bathroom?
“Moisture board plasterboard should be used in bathrooms. But in saying that a lot of houses are the same as yours with normal plasterboard fitted then tiled on top. Unless the water gets in a gap and as you say the tiles are fitted well you should have no issues.
Can you screw through a Vapour barrier?
Yes, where the screws go into the joists, no problem, everything will be clamped. But where the screws miss the joists, then they will just pierce the membrane.
How do I make my kitchen tiles warmer?
The most effective way to warm up any flooring including tiles is to install underfloor heating. It creates a pleasant heat with no cold spots, distributes that heat evenly, and gently warms a room without any wasted energy.
Is Celotex dust dangerous?
celotex is non toxic but the dust gets in your lungs and will cause irritation. The foam may contain some 5% of glass fibre threads and as with rockwool you dont want to be breathing it.
Can you screed on top of insulation?
When it is over insulation, it is normally termed as “floating”. If the screed is on top of insulation there is going to be move “give or “movement” than being laid directly on to a structural substrate. Insulation will have a strength rating. The higher the KPA, the stronger the insulation is.
Do I need insulation boards for underfloor heating?
Do I need Insulation Boards? Many people wonder if it is worth insulating under floorboards and the answer is that yes, it definitely is. Insulation boards are ideal for use with electric underfloor heating as they prevent the heat from the heating system escaping downwards to the subfloor.
Can Celotex be used as a Vapour barrier?
Does kingspan need a Vapour barrier? I use Celotex or Kingspan insulation boards which are foil faced, and then I cover them with separate plasterboard. The cheapest insulated plasterboard which uses expanded polystyrene does NOT have a vapour barrier, so don’t use it!Jun 14, 2020
