Table of Contents
Do you need to replace it when replacing the roof? No you do not have to replace it but you should, the old drip edge is most likely “old” looking and dirty from being outside for so long. If you are making the effort to replace you roof, you should replace everything so the entire roofing system looks nice.
Should I replace drip edge when replacing roof?
Drip edge is the metal flashing that’s installed at the edges of the roof to help control the flow of water away from your fascia and other roofing components. The drip edge has to be replaced when you get a new asphalt roof. It’s actually a code to have it on your roof.
Can I reuse drip edge?
Existing drip edge, vent flashings, step and counter-flashings may be reused when they are in “like new” condition, meaning that they do not show signs of excessive wear, damage or deterioration (for example, corrosion, rust, scoring, tearing or any physical damage from the roof tear-off).
When should drip edge be replaced?
Drip Edge Flashing Drip edge comes in 10-foot strips and attaches to the roof deck before the roofing felt goes on. Unless the old drip edge is in like-new condition, replace it.
Is roof drip edge necessary?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
Do you need drip edge on rake edge?
A drip edge should be installed on the eaves and rakes of the roof, flush with the decking and fascia. On eaves, the drip edge is installed directly to the deck with underlayment installed over it for proper water shedding. 2×4” drip edge should be used on the eaves and 2×2” may be used on the rake.
Does drip edge go on before fascia?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Can drip edge be replaced?
The drip edge is often replaced when new shingles are installed, but it can be replaced at any time. Asphalt roof shingles can become brittle in cold weather, so wait until a warm (but not hot) day to remove and replace eave stripping.
Do you install drip edge with gutters?
It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. If gutters are installed below the drip edge, water can drip behind the gutter and cause damage to the wood supporting the gutter system.
Can drip edge be installed after shingles?
The most popular time to install a drip edge is when new shingles are installed. However, the drip edge can be installed at any time. The materials involved include: a ladder, a flat pry bar, a hammer, tin snips, eave stripping, and galvanized roofing nails.
How much does it cost to install drip edge?
The cost of drip edge Drip edge is always going to be included in your roof replacement. Because of this, it’s going to have an impact on the price you’ll pay for your new roof. The standard drip edge used (aluminum) is going to be around $2.00 a linear foot, including labor to install.
Does drip edge go around entire roof?
Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.
How far should shingles overhang drip edge?
Asphalt shingles should overhang the exterior edge of the drip edge by ¼ to ¾-inch. Check local building code for drip edge requirements prior to the start of your roofing project.
Does GAF require drip edge?
GAF requires installation… of non-corroding metal drip edges at the rakes and eaves when required by local building code. As a matter of good roofing practice, however, GAF strongly recommends that drip edges be installed at the rakes and eaves on all GAF shingle roofs.
What is the difference between drip edge and rake edge?
It involves the point of application in relation to the underlayment and/or eaves flashing. At the rake edge, the perimeter drip edge metal is applied over the underlayment with the appropriate fasteners secured every eight (8) to ten (10) inches on center.
Do you nail drip edge to fascia?
You don’t. The drip edge is attached onto the plywood roof decking before any shingles are installed. And assuming that the roof’s bottom edge has a typical fascia trim, that trim should be in place before the drip edge.
Why is water dripping between gutter and fascia?
If water is dripping behind your gutter, it’s probably because it was installed without any flashing over the back of the gutter. The gutter apron will prevent the dripping. A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter.
