Table of Contents
The thermocouple is likely reacting to an abnormal flame temperature and shutting off the gas automatically. This is why the clicking sound continues. If you furnace begins clicking and the blower turns on and off again, this may indicate a faulty flame sensor.
Why is my electric furnace clicking?
1. Why Is My Furnace Making A Clicking Noise? If your furnace is constantly making a clicking noise then you are likely looking at a mechanical malfunction of some sort. A clicking furnace is often caused when the furnace’s spark igniter tries to ignite the pilot light or burners.
Why does my furnace click when it shuts off?
Typically, when a heater makes a loud banging noise when it turns off, it’s the sound of metal contracting. Once the heating cycle stops, the sheet metal of the ductwork and the metal panels of your furnace cool and contract, producing a ‘bang’ or ‘pop’ that you hear inside your home.
Why is my furnace making a ticking noise?
Clicking – A clicking noise coming from your furnace is typically an indication of a faulty flame sensor or possibly a problem between the ignition and the gas. Squealing – Not unlike a car, squealing coming from your furnace could indicate a faulty belt or a failing fan motor.
Why does my electric heater make popping noises?
When it heats up, the metallic surface experiences internal tension, because metals expand when they heat up. The metallic surface of the space heater releases the tension in sudden bursts, which you perceive as the loud clicking noise.
How do you fix a furnace that clicks?
Loud clicking sounds can be heard when inducer blowers and fan shafts are clogged by buildup or when bearings are worn out. Bearings on the main blower motor might click as the furnace runs because the shaft is rusted or dirty. Cleaning and lubricating the fan shaft will help fix the problem and prevent premature wear.
Can hear your furnace click on but it does not fire up?
The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up. If the sensor or ignitor is dirty, it will need to be cleaned.
How do you know if your furnace ignitor is bad?
Your furnace won’t run: The most obvious sign that your ignitor is bad is that it won’t ignite, and this generally manifests itself in your furnace failing to run when you activate it. One word of caution, though: this can also be caused by other issues, some of which are electrical.
How much does it cost to fix a furnace ignitor?
Here’s the bottom line: Whether for a natural gas furnace, oil, or a propane furnace, replacing a furnace ignitor–including parts and labor–will cost you around $300 – $425 for a qualified contractor to install. Compare that to, say, a draft inducer motor, which will cost $400 – $1,500 to replace.
How do I reset my electronic ignition furnace?
To reset the ignition control module on an electronic-ignition furnace, turn down the thermostat or turn off the power switch. Listen for the sound of the spark or watch for the hot surface ignitor to glow. Next, make sure the furnace’s flame sensor is clean.
Can you clean a furnace ignitor?
If your furnace has a spark ignitor and it’s working haphazardly, it too could be covered with soot, and a blast of compressed air may be enough to clean it. Compressed air can also clean a blocked pilot tube that is causing the pilot flame to burn weakly or not at all.
How often should furnace ignitor be replaced?
According to the Gas Furnace Guide, ignitors have an average lifespan of four to seven years. So, after about seven years, you may have to replace the ignitor; however, you probably won’t have to replace the entire furnace because other parts, such as the heat exchanger, can last more than 15 years.
What causes furnace ignitor failure?
As mentioned above, sometimes the cause of a furnace ignitor failing to ignite is due to a safety issue, such as a clogged air filter, for instance. So, if your furnace is failing to ignite, it’s a good idea to check the air filter. If it looks clogged up, then this is probably the source of the problem.
How long does furnace ignitor last?
No matter which type of ignitor is in your furnace, this chain of events lights your heater so that it blows hot air. Don’t worry—an ignitor that goes bad is common for most furnaces. Fortunately, you can replace the ignitor without replacing the full furnace. Most ignitors last about seven years.
Is it hard to replace a furnace ignitor?
Thankfully, most heating, air conditioning, and ventilation companies sell igniters for most furnace models, including those no longer manufactured. Qualified Technician: Most homeowners will agree that furnace tune-up and replacing an igniter is relatively easy.
How much does a new circuit board cost for a furnace?
A furnace circuit board replacement can cost between $550 – $1,100, depending on how complex your system is.
Is there a pilot light on electric furnaces?
Electric furnaces have pilot lights, the same as gas furnaces. The trend of replacing pilot lights with electronic ignition systems in electric furnaces was similar to the one happening in gas furnaces. That means that before about 2010, most of the electric furnaces with pilot lights were produced.
