How Much Concrete For 4X4 Fence Post

How Much Concrete For A 4×4 Fence Post? Depth 50 Lb Bags 10″-14″ 2 16″-22″ 3 24″30″ 4 32″36″ 5.

How much concrete do I need for a fence post?

How much Post Mix do I need for a fence post? The exact amount of Post Mix Concrete needed will vary depending on the width and depth of the hole, but as a general rule you’ll need about one and a third bags for a standard fence post.

How deep should I bury a 4×4 fence post?

Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).

Is 2 feet deep enough for fence posts?

2 feet is the minimum depth that you should dig your fence post holes for. To dig the holes one-third to one-half of the post’s aboveground height, is a general formula. The deeper you dig the holes, the more stability your fence has.

How much concrete do I need for an 8 foot 4×4 post?

Here in Northeast America, the most common procedure is to dig a 8″ diameter hole approx 2.25–2.5′ deep, and a 4×4 posts is placed in the center. Approx 70–80 lbs of concrete is poured in dry, and then it is packed tight with a bar.

How many square feet does a 50 lb bag of quikrete cover?

Regarding this, how much does a 50 lb bag concrete cover?, as 133 lb concrete = 1 CF, so a bag of 50 lb concrete = 50/133 = 0.375 CF, therefore, a 50 lb bag of concrete approximately cover around 1.5 square feet area upto standard depth of depth of 3 inch for your patio and sidewalk.

How do I calculate how many fence posts I need?

Measure the length of your yard. This will be your fence length. The number of posts you will need is your fence length divided by 6 or 8. For example, a yard of 100 feet with 8-foot placement will require around 13 posts.

How much quikrete do I need for fence post?

1 – 4 bags of concrete per fence post are typically what’s needed. This depends on the type of soil, fence design, height, post size and bag weight. In general the depth of the post’s hole needs to be 1/3 to 1/2 of the above ground height of the post.

How much concrete do I need for a post hole?

A: Finding the right amount of concrete depends on the size of the hole and the size of the post. The diameter of the hole should equal about three times the diameter of the post and the depth of the hole should be about ⅓ to ½ the total length of the pole.

How long will a treated 4×4 post last in the ground?

How Long Will A Treated 4×4 Last In The Ground? (Explained) A treated 4×4 will last 20 to 25 years in the ground if the conditions in the soil and climate are favorable. That number could increase to 40 to 75 years if you install the treated 4×4 in a cement ring rather than the soil.

How big of a hole do I need for a 4×4 post?

The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter. For a six-foot-high fence post, we would need a hole that’s 36 inches deep and 12 inches in diameter.

How many bags of Postcrete do you need per post?

“Usually one bag of postcrete per post is enough, however you can use a two bags per post if you feel this is needed.

Is 18 inches deep enough for a fence post?

The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.

How many cubic feet is an 80 lb bag of concrete?

30 cubic feet, 60 pounds of concrete mix yields . 45 cubic feet and an 80-pound bag yields . 60 cubic feet. One 50-pound bag of Quikrete Fast Setting Concrete Mix yields about .

How many bags of concrete do I need for a 4×4 slab?

As per calculation, for a 4×4 slab at 4 inch thick, generally you will need approximately either 12 bags of 60lb or 9 bags of 80lb of premixed concrete, at 5 inches thick slab, either 15 bags of 60lb or 11 bags of 80lb premixed concrete are required, while at 6 inches thick slab, either 18 bags of 60lb or 14 bags of.

What is the best concrete mix for fence posts?

For a small to mid sized job I recommend going with premixed. The best concrete mix for fence posts I’ve found is Quikrete Fast Setting Concrete Mix in a 50 lb bag. It’s 4000 psi, easy to work with, sets up fast, and doesn’t need to be mixed. Just pour it in the hole and soak with water.

How many bags of concrete do I need for a 10×10 slab 4 inches thick?

The thickness of your 10′ x 10′ slab will determine just how many bags you need. The average thickness of a 10′ x 10′ concrete slab for a shed is 4 inches thick. At 4″ thick, your 10 x 10 slab will take 56 bags of concrete that weigh 80 lbs.

How much concrete do I need for a 10×10 slab?

The amount you will need for a 10 x 10 slab is 1.3 cubic yards, we always add an extra 10% to allow for any slab depth variations or spills that may occur.

How many bags of concrete do I need for 100 square feet?

Number of cement bags are required for 100 sqft 6 inch slab = 11.4 bags.