Table of Contents
Measure the length and width of your driveway in feet. Multiply the length by the width to get surface area and divide the result by three because 4 inches is 1/3 of a foot. You now have the volume of gravel needed in cubic feet. Divide the volume in cubic feet by 27 because there are 27 cubic feet in a cubic yard.
How do you calculate gravel?
Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 21.6 (the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.
How much does a tonne of gravel cover?
Type 3 Aggregate Calculator Therefore if you wish to apply them at a 50mm depth (the normal depth for a driveway) one tonne will cover 14 square metres. For pedestrian pathways, 35mm is normally sufficient in which case 1 tonne will be sufficient to cover approximately 20 square metres.
How many square feet will 5 tons of gravel cover?
Regarding this, “how much area does 5 tons of gravel cover?, typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 5 tons of gravel = 108 × 5 = 540 sf coverage, therefore 5 tons of gravel can cover around 540 square feet or 60 square yards or 50 square meters area for standard 2 inch depth.
How many inches deep should a gravel driveway be?
A standard driveway is between 12 and 18 inches deep. Each of these gravel layers is a minimum of four inches deep, and some folks recommend making each layer as much as six inches. If you have a large area to dig out for your new driveway, the idea of a shovel and wheelbarrow may not be very appealing at this point.
How do I figure out how many yards of gravel I need?
The formula: Number of Cubic Yards = Length (in feet) Width (in feet) Depth (in feet) ÷ 27. Simply multiply the three dimensions together to find the number of cubic feet, then divide by 27 to find the number of cubic yards.
How many yards is a ton of #57 gravel?
Calculate #57 Limestone Gravel Coverage (Square feet) 400 sq ft Volume (Cubic feet) 67 cu ft Volume (Cubic yards) 2.5 cu yd Estimated amount (Pounds) 5,951 lb Estimated amount (Tons) 2.98 ton.
What area will 1 ton of gravel cover?
A ton of gravel will cover approximately 100 square feet, 2 inches deep.
What area does a tonne of 20mm gravel cover?
Based on our 20mm sized stones, 1 bulk bag of gravel will cover approximately 12 sqm at 50mm depth for paths and driveways. Alternatively, 1 bulk bag will cover approximately 16 sqm at 30mm depth. Our 25kg Polybags will roughly cover 0.4sqm.
What is the cheapest gravel for a driveway?
Cheapest gravel for driveways. The cheapest gravel for driveways is crusher run, crushed shells, crushed concrete, slate chips, recycled asphalt, and pea gravel, which all cost $15 to $30 per yard, or less than $1 per square foot when purchased in bulk from a quarry.
How many square feet will 7 tons of gravel cover?
Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel, 100 square feet per ton; 1/2 to 1 inch gravel, 90 square feet per ton; and 1 1/2 to 2 inches gravel, 80 square feet per ton.
How many square feet will 25 tons of gravel cover?
How many square feet will 25 tons of gravel cover:- typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 25 tons of gravel = 108 × 25 = 2700 sq ft coverage, therefore 25 tons of gravel can cover around 2700 square feet or 300 square yards or 250 square meters area for standard 2 inch depth.
How much gravel is in a dump truck?
How many yards of gravel in a dump truck:- a standard sized dump truck is always recommended for your project. It can carry about 15 to 16.5 cubic yards of 3/4″ or pea gravel per truckload. Thus, a dump truck can have capacity to hold 15 to 16.5 cubic yard of gravel per truckload.
Do I need fabric under gravel driveway?
Is it really necessary to put fabric under my gravel driveway? Yes, if you want your driveway to last. Having geotextile fabric under your gravel driveway will prevent you from continually needing to add more aggregate base to your road since the rock will drop into the subgrade layer.
Are there different grades of gravel?
Gravel is classified by particle size range and includes size classes from granule- to boulder-sized fragments. ISO 14688 grades gravels as fine, medium, and coarse, with ranges 2–6.3 mm to 20–63 mm. One cubic metre of gravel typically weighs about 1,800 kg (or a cubic yard weighs about 3,000 lb).
How deep should you lay gravel?
Decorative aggregates should be laid at a depth of 50mm. This ensures proper coverage without revealing the surface below. Laying the gravel too deep will mean you sink into the surface and it becomes difficult to walk across.
How many square feet is 3 cubic yards?
Cubic yard to Square feet Calculator 1 cubic yard = 9 ft 2 0.037 cubic yard 3 cubic yard = 18.7208 ft 2 0.1925 cubic yard 4 cubic yard = 22.6786 ft 2 0.2963 cubic yard 5 cubic yard = 26.3162 ft 2 0.4141 cubic yard 6 cubic yard = 29.7173 ft 2 0.5443 cubic yard.
What does 1 yard of gravel weigh?
One cubic yard of gravel can weigh between 2,400 to 2,900 lbs. Or up to one and a half tons approximately. Generally, a cubic yard of gravel provides enough material to cover a 100-square-foot area with 3 inches of gravel. Keep in mind that some materials compact more than others, so exact coverage may vary.
