Table of Contents
Measure the length and width of the area in feet and multiply the figures together. Multiply your area figure by the depth of gravel that you wish to use, ensuring your measurement is also in feet. If your depth is in inches, divide it by 12 first. You now have a cubic feet volume figure.
How much gravel do I need for my patio calculator?
Gravel Calculation Normally you want a base layer of gravel about 4-inches deep. Four inches is one-third of a foot, so multiply the square footage by one-third to find the cubic feet of gravel you need. For a 120-square foot patio that works out to 40-cubic feet of gravel.
How much crushed gravel do I need calculator?
Multiply the length (L), in feet, by the width (W), in feet, by the height (H), in feet, and divide by 27. This number is how many cubic yards of crushed stone you need.
How much area does a ton of gravel cover?
A ton of gravel will cover approximately 100 square feet, 2 inches deep.
How do you calculate gravel for a driveway?
Measure the length and width of your driveway in feet. Multiply the length by the width to get surface area and divide the result by three because 4 inches is 1/3 of a foot. You now have the volume of gravel needed in cubic feet. Divide the volume in cubic feet by 27 because there are 27 cubic feet in a cubic yard.
How many square feet will 5 tons of gravel cover?
Regarding this, “how much area does 5 tons of gravel cover?, typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 5 tons of gravel = 108 × 5 = 540 sf coverage, therefore 5 tons of gravel can cover around 540 square feet or 60 square yards or 50 square meters area for standard 2 inch depth.
How many yards is a ton of #57 gravel?
Calculate #57 Limestone Gravel Coverage (Square feet) 400 sq ft Volume (Cubic feet) 67 cu ft Volume (Cubic yards) 2.5 cu yd Estimated amount (Pounds) 5,951 lb Estimated amount (Tons) 2.98 ton.
How Much stone do I need calculator?
Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 21.6 (the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.
How many yards are in a ton?
Regarding this, “how many yards in a ton?”, generally for estimating purpose 1 yard of gravel weighs around 3000 pounds and 1 US ton = 2000 pounds, so yards in a ton = 2000/3000 = 0.66 cubic yards, therefore, there are 0.66 yards in a ton.
How deep should you lay gravel?
Decorative aggregates should be laid at a depth of 50mm. This ensures proper coverage without revealing the surface below. Laying the gravel too deep will mean you sink into the surface and it becomes difficult to walk across.
How many sq ft are in a ton?
600 sq ft Area (Square Feet): BTU Tonnage 600 sq ft 12,000 BTU 1 Ton 900 sq ft 18,000 BTU 1.5 Tons 1,200 sq ft 24,000 BTU 2 Tons 1,500 sq ft 30,000 BTU 2.5 Tons.
How much area does a ton of 20mm gravel cover?
Based on our 20mm sized stones, 1 bulk bag of gravel will cover approximately 12 sqm at 50mm depth for paths and driveways.
How many square feet will 7 tons of gravel cover?
Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel, 100 square feet per ton; 1/2 to 1 inch gravel, 90 square feet per ton; and 1 1/2 to 2 inches gravel, 80 square feet per ton.
How many inches deep should a gravel driveway be?
A standard driveway is between 12 and 18 inches deep. Each of these gravel layers is a minimum of four inches deep, and some folks recommend making each layer as much as six inches. If you have a large area to dig out for your new driveway, the idea of a shovel and wheelbarrow may not be very appealing at this point.
How deep should my gravel driveway be?
Driveway Layers A gravel drive should have a first layer of baseball-sized stones at least 4 inches deep. According to Tim Carter of AskTheBuilder.com, each layer thereafter should be 4 inches thick and in gradually smaller stone.
How many inches of stone do I need for a driveway?
According to the Home Depot, 4 to 6 inches of rock or gravel is needed for a driveway. Convert your estimated rock depth in inches to feet by dividing the number of inches by 12.
How many square feet will 16 tons of gravel cover?
How many square feet will 16 tons of gravel cover:- typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 16 tons of gravel = 108 × 16 = 1728 sq ft coverage, therefore 16 tons of gravel can cover around 1728 square feet or 192 square yards or 160 square meters area for standard 2 inch depth.
How much gravel is in a dump truck?
How many yards of gravel in a dump truck:- a standard sized dump truck is always recommended for your project. It can carry about 15 to 16.5 cubic yards of 3/4″ or pea gravel per truckload. Thus, a dump truck can have capacity to hold 15 to 16.5 cubic yard of gravel per truckload.
How many cubic feet are in a ton of gravel?
How much is a ton of gravel? A ton of gravel with average-sized pebbles is about 0.705 cubic yards, or 19 cubic feet, assuming it has been screened for debris and contains no leftover dirt, sand, etc.
