Table of Contents
Install Fascia Boards Installing fascia boards is a common practice to hide the ends of composite decking boards. Like picture framing, it gives the decking a stylish and sleek look while hiding the exposed ends. The difference is, you will install it on the sides, directly over the edges and the rim joists.
How do you finish composite decking edges?
Conclusion. How to finish the edge of a composite decking is simple if you use picture framing to cover the board edges. You can also paint the edges, glue a veneer cap to the ends, attach a raised fascia board or add a composite corner trim to create a consistent look.
What do you do with cut ends of composite decking?
Sealing the ends with lumber wax will help prevent moisture absorption. Kim Katwijk The cut ends of composite decking will absorb moisture and can swell, as shown here. Sealing the end cuts with lumber wax will help prevent swelling.
How do you cover deck board ends?
Another way to hide the ends is to install a border/perimeter board around the outside edges of the deck (bottom). This method can really dress up your deck, especially if you choose an accent color for this board. The downside of a perimeter board is that it requires extra framing underneath.
Can you paint the ends of Trex decking?
A: You are correct. Vintage Trex decking and other brands of composite decking made of a uniform mixture of wood fibers and plastic can be painted or even stained. Newer styles of composite decking capped with a shell of different material on the top and sides of boards cannot.
How much overhang should a Trex deck have?
Trex is a popular composite material with a maximum overhang of 102mm or around 4 inches. Between one and two inches of deck board overhang is ideal when you attach an outer fascia board, or at least 1 ¾” to 2 ¾” of overhang before installing the fascia.
What is Trex Trim?
Along with new profiles, Trex has improved the surface aesthetics of its moulding offerings with a matte finish that is aligned with contemporary home design trends and was developed as a direct result of homeowner demand.
Can you sand the edge of composite decking?
No, sanding composite decking could cause damage and void the warranty. MoistureShield’s built-in protection stands up against weather and wear. Our Elevate and Vision series feature a protective polymer cap to resist fading and staining.
Do you need to seal the ends of Trex?
Low-Maintenance With Trex Composite Decking You won’t ever need to seal or stain the deck, and you certainly don’t have to (and shouldn’t) paint it. And since Trex is a composite material, you don’t have to carry out long-term maintenance such as replacing rotted deck boards.
Can you use Behr DeckOver on composite decking?
For weathered composite surfaces use BEHR PREMIUM ADVANCED DeckOver® to bring new life to old composite decks. See our how-to’s “Prep Your Wood: Weathered Wood” for guidelines on properly preparing your composite surface. A quality pump sprayer may be used when applying wood finishes.
Why does composite decking have grooves?
Grooved-Edge Decking Appearance: The primary reason people choose grooved decking is because they don’t want to see deck screws messing up their deck’s surface. Grooved decking has slots cut into both sides so it can be installed with hidden fasteners.
How do you refresh Trex decking?
Remove larger items of debris by hand or with a broom, then use a water hose to spray down the surface of the decking. Combine half a cup of apple cider or white wine vinegar with a gallon of water and a cup of baking soda — this is the cleaning solution recommended by Trex for its decking boards.
How far can a deck board overhang?
The American Wood Council states that cantilevers are limited to 1/4 the span of the joists. Joist Spacing (o.c.) Maximum allowable overhang cannot exceed 1/4 of the actual main span.
Can you overhang composite decking?
Like any other deckings, you can design composite decking to have an overhang. However, it should be a part of your deck planning and layout design. You can create overhang using several methods. For instance, after installing the decking boards, you may opt to leave a few inches off the boards.
Does a deck need an overhang?
When installing decking boards, be sure to allow for enough overhang to cover the fascia board and whatever additional amount you prefer. This means the installed deck boards should have at least 1.75 to 2.75” overhang before the fascia is installed.
How much overhang should a picture frame deck have?
Fortunately, there’s not much to it. A typical overhang for wood decking, or flooring, or stairs for that matter, is 1”. At each corner, measure back from the outside of your framing, (or trim if the deck is trimmed), the width of your decking minus 1”.
Do you have to picture frame Trex decking?
Many PVC and Trex composite decking products are not the same color all the way through, so you’ll want to cover the ends. One solution is to “picture frame” the deck by installing Trex deck boards around the perimeter. Pro tip: A picture frame creates a professional look but does require additional framing.
Does Trex make trim pieces?
“Trex continues to grow its innovative TrexTrim product portfolio in order to provide building professionals with the most expansive line of high-performance, low-maintenance trim products on the market,” said Ronald W.
What is Trex Trim made of?
Trex decking is made from 95% recycled materials, including reclaimed wood and sawdust as well as recycled plastic from many common household items, such as the plastic overwrap on packaging for paper towels and toilet paper, dry cleaner bags, newspaper bags, grocery and shopping bags.