How To Repair Trex Decking

Here are some methods you can use to fix scratches on your composite deck: Fill nicks and scratches with an epoxy-based filler and a putty knife. Try the heat method. Replace scratched boards with new ones. Consider consulting the manufacturer or retailer about your scratched decking.

Can Trex be repaired?

If you notice a scratch or damaged area on your Trex decking, fret not! If you have a small scratch or chip, use a composite deck repair kit. With a few tools, you can easily repair your deck and enjoy your patio.

Can composite decking be repaired?

If the boards on your composite deck have chips or small cracks, you may be able to repair them by using a composite deck repair kit — depending on the materials and the manufacturer of your deck’s boards.

How do you remove scratches from Trex decking?

Removing Scratches from Composite Decking Use a Heat Gun – Using a heat gun is one of the most effective ways to eliminate the scratches on your decking. Try a Wire Brush – Another popular method that you can try is by using a wire brush.

How do you fill Trex holes?

Fill small holes, using a putty knife, with a mixture of fine composite board shavings and silicone caulk. The consistency of the mixture should be thick enough that it will not seep out of the bottom of the hole. Match the color of the caulk to the deck boards.

How do you fix a crack in a composite deck?

Sand the crack and filler using a hand-block with 100-grit sandpaper. Use strokes parallel to the board to sand the filler flush with the surface of the crack. If the filler has shrunk and created a slight depression, fill the depression with more composite filler and let it dry.

Can you caulk Trex decking?

Trex RainEscape Butyl Caulk is specially designed for use with Trex RainEscape Down Spouts (choose Tan or Black) and Troughs (also available in Tan or Black) on floor joist, rim joist, and ledger board overlaps.

Can you caulk composite decking?

Make sure to leave gaps between the ends of each board as well. However, there are a few ways to do it without reinstalling the whole decking. One of the ways to do it is by caulking. It is often used in wooden decking, but it may also work in composite decking.

How do you repair a composite?

Basic Repair Process Inspect to assess damage (extent and degree) Remove damaged material. Treat contaminated material. Prepare repair area. Complete composite repair. Inspect repair for quality assurance (e.g. delaminations, inclusions, proper cure, etc.) Restore surface finish.

Does composite decking have gaps?

As temperatures fluctuate, composite deck boards will naturally experience thermal expansion and contraction. That’s why the board ends should never be installed tight against one another. There should always be a slight gap.

How long do composite decks last?

Composite decking requires minimal upkeep and can last between 25 and 30 years. On average, plastic decking has a similar lifespan to composite decking and can last nearly 30 years.

Can you screw composite decking?

The answer is yes for a solid composite decking (must be pre-drill and must check with manufacture). You can not drill or screw through a hollow composite deck as the screw will become loose and rise in time . Like the usual wooden decking boards, you can also screw down a solid composite decking.

Can you scratch Trex decking?

Newer-generation Trex decking holds strong against potential damage. All of our decking lines are scratch resistant, protecting your space against nicks, cracks and splitting.

How do I stop my composite deck from scratching?

Furniture pads are a great way to protect your decking, especially if you tend to move furniture around. Those with metal bottoms are more susceptible to making scratches, so take particular care with them. There are many peel-and-stick protectors available in the market.

How do you fix burn marks on a composite deck?

First wet the deck down with a hose. Next, mix together one teaspoon of grease-fighting detergent with around a gallon of water. Soak a stiff-bristled brush in the detergent mix and then scrub the burn mark going in the direction of the grain. Rinse the soapy water off and allow the deck to dry.

Can I drill through Trex?

Composite decking such as Trex can be cut, drilled, and fastened just like traditional wood, but there are a few tricks you should know to make your project easier, and provide a more professional finish. The decking should be at the same temperature as the area where it will be installed.

How do you repair composite wood?

Repairing Particle Board With Wood Filler Remove loose chips or rotted wood from the damaged area with a stiff-bristled brush. Fill the damaged area with wood filler using a putty knife. Sand the patched area with a medium-grit sanding block. Sand and smooth the wood filler with a fine-grit sanding block.

Can you paint composite deck boards?

Yes, composite decks can be painted, preferably using latex paint for durability and reduced fading. The higher the quality, the better. Painting a composite deck doesn’t affect its longevity, but it does cover any staining or patchy appearance due to sun-bleaching in exposed areas. It’s like having a brand new deck.

Can composite decking break?

Decking boards made of composite materials don’t have the structural integrity of real wood, and can delaminate and even break.