Table of Contents
How do I fix E1 F9 error on Whirlpool washer?
How to Fix Whirlpool Washer E1/F9 Error Codes Try a Reset. Sometimes an error code is caused by a control board glitch, where resetting the washer is all it takes to resolve the error code. Check your Detergent. Check the Drain Hose. Clean the Filter. Check the Drain Pump. Check the Wiring.
How do I fix error E1 F9 on Maytag washer?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation. Use drain hose form and attach securely to drainpipe or tub.
What does E01 and F09 mean on a washing machine?
Accepted Answer. Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.
How do I fix error code F9?
Reset the Oven Sometimes, the F9 error code is the result of an electrical fault that has magnetized the circuitry. Resetting the oven by disconnecting the power for five minutes will demagnetize the circuitry and resolve the F9 error.
How do I fix E1 error on my washing machine?
E1 – water inlet alarm Check that the water faucets are not closed. Check that the water pressure in the house is over 20 kPa. Clean the inlet hose filter screens. Be careful not to remove or disturb the screen placement. Check that the drain hose is not below 27½” (700 mm) from the floor.
How do you unclog a washing machine drain?
To unclog a clogged drain, first fill a bucket with boiling water and a pack of baking soda. Remove the drain pipe from your washing machine and slowly pour the water into the drain using a funnel. Wait a few minutes and test if it keeps draining if you pour water into it.
How do you manually unlock a Maytag washer?
Washer door unlock fix: Cancel the wash cycle, wait for it to drain the water and the door should unlock, OR pull the green string near the detergent area, OR pull the lever on the bottom of the door switch, OR unplug the washer for 5 minutes to reset. These 4 things should unlock your washers door.
How do I reset my Maytag washer?
The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
What does E1 F9 mean on a Whirlpool washer?
If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Remove any clogs from drain hose.
What does E01 mean on a washing machine?
E01 – there’s an issue with the lock, its wiring or connection to the control board. Check the door is closed properly and the wiring is intact. E02 – the machine has failed to fill with water during its allocated time.
How do I clear the error code on my Whirlpool washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle. Remove items from the drum and restart the Clean Washer cycle.
How do I clear F9 code?
How to Remove the F9 Code From Maytag Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. Open the oven door and check the door latch. Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. Press the oven door shut gently. Test the oven.
How do I clear my Whirlpool F9 code?
Reset the appliance Power unit down by turning off the circuit breaker(s) for one (1) minute. Monitor the range or oven for one (1) minute to ensure the error code does not display again. Verify the range or oven operation.
What is an F9 code on a Whirlpool range?
F9 – Oven Door Lock Failure – Check door lock switches and wiring. Check for stuck lock switch. FH – Detects No Water Entering Machine or No Pressure Switch Trip – Select ‘cancel’ twice to clear this code. If there is NO water in the unit, make sure the valves are turned on all the way.
How do I fix E1 error?
The Generic Approach Turn off the air conditioner and unplug it. Hold down the power button, and keep it depressed while you or someone else plugs it back in. Keep the button depressed while the fan and condenser cycle run briefly and cycle off again. Unplug the air conditioner again and plug it back in.
How do I fix E1 error on LG washer?
Turn off the home’s hot and cold water supply taps/valve. Remove the water inlet hoses from the washer. Ensure to have a bucket to drain the remaining water from the hoses. Check the inlet filters on the inlet valves of the washer, inspect for any mineral deposits or other debris that may be clogging them.
How do I reset my washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
