Table of Contents
UL is the code for unbalanced load. Open the lid and redistribute your wash to balance the weight of the wet items, then restart the machine. Repeat until the washer spins without thumping.
Why does my washer keep saying unlevel?
A front load washer is much heavier and larger than its top load counterpart. An out-of-balance condition can result from an unlevel machine, or a worn out tub bearing that allows radial play in the wash basket shaft which causes the entire tub and basket assembly to spin wildly out of control.
How do you reset the code on a Maytag washer?
To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute. Items were detected in the washer during the Clean Washer cycle.
What does uL mean on washer?
uL. (none) Unbalanced load. uL is displayed when the machine/motor control detects an off-balance load and remains on while the washer runs a mini-cycle to rebalance the load.
Why does my Maytag washer keep getting unbalanced?
Common solutions for: Maytag ob – Off Balance Washer vibration can occur if one or more of the shock absorbers is broken or worn out. Check the absorbers to be sure they are installed correctly and in the right position. Sometimes when a washer is moved the shock absorbers separate and have to be put back together.
What does UL mean on a Maytag Bravos XL washer?
Your washer is off balance or the load is unbalanced If uL (unbalanced load) appears in display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue.
Does Maytag washers have a reset button?
Resetting a Maytag coin-operated washer Hold down the Delicates and Knits button for five seconds. The washer’s LED display should now flash and start to blink, which means the error codes have been resolved and the washer has reset.
How do you do a factory reset on a washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
What does UL mean on electrical equipment?
UL stands for Underwriter Laboratories, a third-party certification company that’s been around for over a century. UL was founded in 1894 in Chicago. They certify products with the aim to make the world a safer place for both workers and consumers.
How do I fix the UL code on my Kenmore washer?
You can try to clear the Error Codes; Unplug the washer for 1 to 2 minutes. Disconnect the U.I. (touch pad). Plug the washer back in for 1 to 2 minutes.
How do I reset my Maytag high efficiency washer?
Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.
How do you balance a Maytag washer?
Place a 4-foot level across the front top of the washer. Adjust the front legs if necessary until the front is in balance. Loosen the retaining nut with the adjustable wrench and turn the feet as necessary until the front balances. Tighten the nut with the adjustable wrench.
How do I know if my washing machine balance ring is bad?
The balance ring is filled with fluid. This fluid helps to dampen the vibration of the washer. If this fluid leaks out of the balance ring, the washer tub will vibrate and shake during operation. Check the balance to determine if is still filled with fluid.
What is PowerWash on Maytag Bravos?
Use the PowerWash® cycle on select Maytag® washing machines to help remove everyday tough stains in a single wash by using a combination of extra wash action and heated water.
Why does my Maytag washer stop mid cycle?
Maytag Washer stops mid cycle If the door lock is defective, the washer may stop mid cycle. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.
Why is my washer not resetting?
Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
How do you reset a front load washer?
What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a “reset” of the washer.
Is UL required?
Having a UL listed certified unit is not legally required. It is, however, a common practice because many large companies will only buy equipment that has passed the UL safety tests. Having a tested product shows that the equipment meets a nationally recognized safety standard.
What is UL code?
<ul> HTML Tag The <ul> element is used to define an unordered list of items. Use an unordered list to contain <li> elements that do not need to be presented in numerical order and can be rearranged without changing the meaning of the list. Display block Usage semantic. Contents [hide] 1 Code Example.
