QA

How To Install Fascia Boards

How hard is it to install fascia board?

Fascia boards are found around the edges of your roof and usually support your home’s rain gutter system. Luckily, replacing a fascia board is as easy as taking out the old board and fitting a new one in its place. Once you’ve installed a new board, all you need to do is seal the seams and paint it to match your home.

What size should fascia board be?

Fascia Board Sizes Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction. Therefore, the more common fascia board sizes are 1×6 or 1×8.

How do I fix my soffit and fascia?

Soffit and Fascia Repair Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. Remove Rotted Fascia. Remove the rotted section of fascia. Remove Old Soffit. Pull down to remove the old soffit. Remove Rotted Rafter. Attach Cleat. Attach New Rafter. Seal Replacement Soffit. Attach Replacement Soffit.

Should I screw or nail fascia?

Hometime.com recommends using screws instead of nails when replacing fascia to avoid jarring the existing framing with hammering.

What kind of nails do you use for fascia?

What nails do you use for fascia? Galvanized nails. Aluminum nails. Stainless steel nails.

How many nails do you need for fascia board?

For replacement fascias (16mm+ thickness) – Use 65mm nails, two nails on each rafter end. This is because the fascias have to support the weight of the bottom row of tiles, the gutter and anything in the gutter.

Can I use 2×4 for fascia board?

Install 1×6-80″ fascia boards to the 2×4 trusses. Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt.

What is the best material for fascia boards?

Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.

Can you use pressure treated wood for fascia boards?

Purchase pressure-treated lumber to replace your fascia boards as a way to extend the life of the repair. Pressure-treated lumber is designed for outside applications and resists rot, moisture and insect damage. Cut the new lumber to size and secure it to the rafter ends with galvanized finish nails.

What goes on first fascia or soffit?

Fascia and soffit are installed after the roof installation is finished. It is ideal that soffit and fascia materials be installed before you place tiles or any other type of roofing material on the roof. There are different types of finished and variations that can be used for the soffit.

How do you attach fascia to roof trusses?

Instructions for How to Attach Fascia Board to Roof Trusses Mark the place closest to the end of the board that aligns with the center of a joist. Use the carpenter’s square and pencil to put a straight line at the mark. Cut the board with a miter saw. Position the board against the trusses and nail it in place.

What is the best wood to use for a fascia board?

Many different types of wood are suitable for fascia boards. Spruce, pine and fir are all popular and relatively inexpensive options. However, some roofers prefer to use cedar, cypress or redwood for fascia boards. While they are more expensive, these woods better resist moisture, even when left unsealed.

Can you use 2×6 for fascia?

Around here everyone uses 2×6 fascia and then covers it with aluminum fascia. If you are leaving the fascia as wood to be painted then the finished face board is better to wider. So you could use 2×4 frame work and 5/4 or 1×6 fascia boards.

What timber do you use for fascia boards?

Timber: Popular hardwood and softwood timber species for fascia board are western red cedar European oak, Utile, Iroko, Douglas fir, Larch and Accoya. The latter is an extremely durable sustainable option.

How do you seal fascia boards?

How to Seal Fascia Gaps in a Roof Inspect the fascia boards for damaged areas. Set a ladder up to gain access to the fascia boards. Start at the end of a fascia board and caulk the corner edge where two boards meet. Move to the next fascia board and repeat Step 3 to caulk the entire board and the corner joints.

Can you put fascia over existing wood?

Hi yes you can buy upvc capping fascias and soffits. However you must make sure that the original woodwork is of sound condition. As you shouldn’t cap over any rotten wood. And make sure that you use starter trim to fit the soffits.

Should fascia be face nailed?

Always nail underside of fascia as shown. Never face nail fascia. *Keep nails lined up with soffit V-grooves for best appearance. Nail every 24″, but do not nail too tight.

How much do you overlap fascia?

NEVER ‘face nail’ fascia. DO NOT drive nails tight — fascia must be ‘hung’, only snug to soffit, to allow expansion and help prevent distortion. Allow at least 1” overlap of fascia where lengths meet.

What’s the difference between soffit and fascia?

An exterior soffit is located on the span beneath the rafter tails, while the fascia is the exposed horizontal band you see at the end of the rafters. These architectural elements found along the eave area do more than just add visual interest and give a finished look to your home.