Table of Contents
What is the best board to use for fascia?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.4 days ago.
How much is a piece of fascia?
Fascia Board Prices. Fascia boards are typically sold by the linear foot for a cost between $1 and $20 per foot, depending on the type of material. Fiber cement is sold by the square foot, between $1 and $5.
What size boards are used for fascia?
Fascia Board Sizes Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction. Therefore, the more common fascia board sizes are 1×6 or 1×8.
What can I use instead of fascia board?
Vinyl. Vinyl siding is a common alternative to fascia board. This type of rafter facing does not rot or wear as quickly as fascia board under the same weather conditions.
Can you use Hardie board for fascia?
HardieTrim board is a decorative non-load bearing trim product. Do not use HardieTrim to replace any structural component. HardieTrimboards can be fastened directly over a 2x sub-fascia or directly to rather tails.
Should fascia board be treated?
Should the fascia board be pressure treated? – Quora. It’s not necessary to use pressure-treated lumber for fascia. In fact, most planking sold for fascia is not pressure treated. However, it is vital that the fascia be primered and completely painted with a good quality exterior enamel or acrylic paint.
How long do fascia boards last?
The average lifespan of wooden fascias is usually between 20 – 30 years if they have been maintained. The type of timber used and the quality of the original installation will affect how long they last. If wooden fascia boards are not maintained, they could need replacing in as little as 5 to 10 years.
What’s the difference between soffit and fascia?
An exterior soffit is located on the span beneath the rafter tails, while the fascia is the exposed horizontal band you see at the end of the rafters. These architectural elements found along the eave area do more than just add visual interest and give a finished look to your home.
How thick should fascia be?
Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick – our most common range is the 18mm Replacement Fascia.
Can I use common board for fascia?
Wood Is a Common Fascia Material Cedar is a popular fascia wood and redwood is another. That’s because both of these wood species have some natural rot-resistance, even when unpainted. If you prime and paint the fascia, you can also make them out of fir, spruce or pine, which are all less expensive.
How wide should a fascia be?
Standard gutter size for residential homes is five or six inches. At the backside of a 5 inch gutter, the fascia board mounting area will be four inches tall. On a six inch gutter, the mounting area is 5 inches.
How do you fix rotted fascia?
Soffit and Fascia Repair Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. Remove Rotted Fascia. Remove the rotted section of fascia. Remove Old Soffit. Pull down to remove the old soffit. Remove Rotted Rafter. Attach Cleat. Attach New Rafter. Seal Replacement Soffit. Attach Replacement Soffit.
Can you use 2×6 for fascia?
Around here everyone uses 2×6 fascia and then covers it with aluminum fascia. If you are leaving the fascia as wood to be painted then the finished face board is better to wider. So you could use 2×4 frame work and 5/4 or 1×6 fascia boards.
Can I use 2×4 for fascia board?
Install 1×6-80″ fascia boards to the 2×4 trusses. Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt.
Is Hardie trim discontinued?
While your preferred siding brand may have discontinued production for some of their products, you should not be afraid as many options are available. For instance, recently, James Hardie has discontinued their trim supply in 2021 for the Pacific Northwest.
Can cement board be used as fascia?
Soffits and fascia board We used fiber cement board to close in the soffits and cover the fascia of the house. Any rotted fascia boards should be replaced prior to covering. The fiber cement board, although durable, is not structurally adequate to support the eaves on its own.
What sizes does Hardie board come?
HardiePanel vertical siding is 5/16 in. thick and is available in 4×8, 4×9 and 4×10 sizes. Please see your local James Hardie dealer for texture and size availability. HardiePanel vertical siding is available as a prefinished James Hardie® product with ColorPlus® Technology.
Can I use treated lumber for fascia board?
It’ll last a long time if you have the proper detail on your home. But pressure treated lumber is not used for fascia boards.
What type of wood is used for soffits?
Standard soffit material is 3/8- or 1/2-inch-thick exterior plywood in pine (or similar softwoods) or cedar. Common, but much less durable, is Masonite or similar fiberboard soffit, as well as much more weather-resistant fiber-cement.
