Table of Contents
What are closet rods made of?
Strength: HARDWARE DECOR offers closet rods constructed of three different materials: steel, stainless steel and aluminum. Closet rods made from steel are chrome plated. In addition to being the strongest, they are also very resilient.
How long can closet rods go without support?
If your closet rod is longer than 48 inches, you will need support. However, regardless of how long the closet rod is, if you’re hanging heavier items such as winter jackets, then you will want support no matter what.
How do you install a closet rod in drywall?
To securely install a closet rod in drywall: Measure the size of the space where the closet rod will go. Buy a closet dowel rod and cut it to length. Choose a wall bracket that can be positioned so that you can screw it into wall studs. Mark the place where your first bracket will be installed. Drill pilot holes.
Do closet rods need to be in studs?
Basic Installation It should be placed in front of a stud so you can screw into the stud to give it support. The typical height of a closet rod is from 60 to 80 inches, and both brackets should be at the same height, or the hooks you hang from the rod will slide to one end.
What kind of pipe do you use for a closet rod?
A length of galvanized steel or black iron pipe makes an unassuming and easily deployed closet rod. You’ll need a custom-cut length of pipe, which you can get at any hardware store. The service technician can also rethread the cut end for you so you can screw a threaded flange onto each end.
How much weight will a closet rod hold?
Aluminum Anodized Elite 1-5/16”: Up to 80 lbs. Stainless Steel 1-1/16”: Up to 95 lbs. Steel Polished Chrome Round 1-1/16”: Up to 110 lbs. Steel Polished Chrome Round 1-5/16”: Up to 170 lbs.
How many brackets do I need for closet rod?
Adjustable Closet Rod 1 TM Page 5 TM NOTE: Recommended 16″ bracket spacing. Maximum 32″ bracket spacing. First, measure the width of your closet. Measure 11-1/2″ from the rear closet wall.
How deep is an average closet?
The standard minimum depth for a reach-in closet is 24 inches, but a closet intended to store coats or other bulky hanging items may need to be as deep as 28 inches. A closet less than 22 inches deep isn’t deep enough to allow hanging clothes.
How far should closet rod be from shelf?
A minimum of 10 inches is best, but it’ll depend on the size of your hangers. If there is a shelf above the rod, determine the vertical distance from the rod to the shelf; two inches should be suffice.
What is the strongest drywall anchor?
Traditional metal toggle bolts are the strongest of the bunch, but they’re not the simplest to install because they require drilling a hole that’s approximately three times wider than the diameter of the bolt (necessary to insert the anchor).
Do closet walls have studs?
Closet shelves are usually anchored to the wall where the mounting screws can grab wall studs. If your walls are masonry, you likely don’t have studs at all. You’ll need the proper materials and methods to build a stud-free closet shelf.
How do you hang a closet rod from the ceiling?
Draw a straight line on the ceiling at right angles to the joists using a yardstick or straightedge tool as your guide. Make the line the length of the closet rod you purchased for the project. Put the line at least 12 inches from the back wall of the closet to allow room to hang clothes hangers on the clothes rod.
How do you build a closet in a small room?
How To Easily Add a Closet to a Small Space Place your closet items where you would like to keep them. Remove the Legacy Panel Room Divider out of the box. Fold the room divider around your items. Ta-da! You have added a closet to your room!.
Can you hang a closet rod without a stud?
Installing a closet rod in a closet without conveniently located studs is a simple job that requires no special tools or advanced carpentry skills. Closet rods are typically held by flange-type sockets that are attached to the wall, screwed into framing studs.
How far apart are studs?
The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.
How much weight can drywall anchors hold?
Toggle bolts are the types of drywall anchors that can support up to 50 pounds, while steel hollow-wall anchors have a drywall anchors weight limit of up to 100 pounds.
How much weight can a screw hold in drywall?
Screws Help Hold the Weight on Drywall Using several screws that are #4 or larger into a wall stud can hold up to 100 pounds or more. You want to make sure they can go at least 1 inch into the stud to be secure. If you are hanging a shelf that will have books on it, this is the perfect hardware.
What to do if there is no stud in the wall?
In most situations you can use a hollow-wall anchor, which is designed to attach to the wall in the hollow spaces between the studs. Hollow-wall anchors come in a wide range of sizes and styles for use on virtually any wall, including drywall, plaster, and even hollow concrete block.
Can PVC be used as closet rod?
The PVC pipe was much less expensive than buying custom closet rods and it worked just fine as the closet rods. I put in an extra bracket to support the top rail and prevent sagging in the middle.
What size pipe for clothes rack?
You’ll Need: Two 1/2″ x 60″ black steel pipes, Two 1/2″ x 48″ black steel pipes, Four 1/2″ x 8″ black steel pipe nipples, Two 1/2″ x 2 1/2″ black steel pipe nipples, Six 1/2″ x 1 1/2″ black steel pipe nipples, Six 1/2″ black tees, Four 1/2″ black 90 degree elbows, Four 1/2″ galvinized floor flanges, Two 1/2″ black Jun 9, 2012.
