Table of Contents
How to Arrange Gas Logs Place the largest ceramic logs on the bottom to serve as the foundation for the fire. Leave 2 inches (5 centimeters) between logs. Make sure none of the logs is blocking the gas flow. Arrange smaller logs on top of the foundation logs.
How do you use ceramic logs?
These logs can be placed in many different types of fireplace spaces. The pipes pump invisible gas through holes in the logs. When the gas logs are ignited, the ceramic logs will produce a steady flame. As propane or natural gas is pumped through the pipes, it burns harmlessly on the surface of the ceramic logs.
How should logs be placed in a fireplace?
The Chimney Safety Institute of America recommends that this layer of logs be placed in a fireplace with the ends facing towards you. These logs should be packed tightly together horizontally so that the fire can be easily transferred between them when the flames reach this layer.
What do you put in the bottom of a gas fireplace?
Silica sand is used in the bottom of the burn pan of VENTED NATURAL GAS log sets. The gas is dispursed though the sand spreading it around before it is ignited. This gives you more flame action in your gas logs. Replace the sand every few years to keep your flames dancing.
Where do you put rock wool in a gas fireplace?
Do not remove or lift your gas burners when installing glowing embers. Place gas logs in the exact same position they were in beforehand. Insert the glowing embers directly below the fireplace burner. Do not put embers on, between, or above your gas log set.
What is the purpose of ceramic logs?
Refractory ceramic gas logs are made of a mixture of cement and ceramic, which allows them to give off more heat than other types. They tend to last longer and are more durable than other options thanks to their ability to withstand very high temperatures. They can be used in both vented and ventless fireplaces.
Can you burn ceramic logs?
Ceramic fiber logs are better at resisting flame damage and some glow when heated. But they do break down with age, and they don’t look quite as realistic. You can buy vented logs for gas fires and burn those in any fireplace that’s designed to burn wood, as long as it has a gas line.
Do ceramic logs need to be replaced?
A: In the average home, a well-maintained vented log set with ceramic logs will last 10 or more years. A well-maintained vent-free log set with ceramic logs can also last a long time, but, if heavily used, will begin to wear in 3-5 years.
How do you put firewood in a fireplace?
Start by placing two pieces of firewood on the grate in your fireplace. Now crumple newspaper, which is your tinder, and place it between the firewood. Place the kindling on top. Add one or two more pieces of firewood on top of the other logs, and be sure to leave enough room for air to circulate around the logs.
How do you stack wood in a fireplace insert?
First, you place your largest pieces of wood on the bottom of the fireplace—ends at front and back. Next, place 4-5 smaller levels of wood on top until that stack fills about ½ the height of the fireplace. The kindling will be on top, and can begin as sticks, and end with wood shavings and crumbled bits of paper.
Do I need vermiculite in my gas fireplace?
Vermiculite is mostly used for Propane (LP) gas logs. It is poured into the burner pan to aid the heavier LP gas to spread across the burner more effectively.
Can you use lava rocks in gas fireplace?
Lava rock is suitable for use in all indoor and outdoor propane or natural gas firepits and can also be used indoors and outdoors in all your landscaping and special project needs. Lava rock is maintenance free but we do recommend the rock is removed from your firepit once a year and rinsed off with clean water.
What is vermiculite used for in fireplaces?
Vermiculite is a light weight naturally occurring mineral which is an excellent heat insulator. It can be used to pour back down the chimney filling the void between the brick chinmey and the flexible flue liner. Vermiculite can also be used to backfill the void behind cast iron fireplaces and clay fire backs.
How do you arrange stones on a gas fire?
The pebbles should be positioned so that the arrows always point towards the back of the fireplace opening. When located into position the stem of each arrow should be at 90° to the rear of the fireplace opening (See figure 3). 5. Hold pebble ‘1’ upright with the arrow pointing to the top.
How much rock do you put in a gas fire pit?
For your gas fire pit to work the way it was designed you’ll need to get the amount of lava rock you put in the burner tray right. Most gas fire pits need 2-4 inches of lava rock but your situation may be different.
Do you cover the burner with lava rocks?
Each of these forms of fire pit media are intended as a decorative addition to your fire pit; however, we strongly recommend using either fire glass or lava rock to cover your fire pit burner.
How long do ember fibers last?
Embers can last up to five years depending on how frequently you use your fireplace.
How long do glowing embers last?
A typical fireplace requires around 1oz of embers (depending on size and how dense it is packed) and we recommend replacing your embers once per year. That means this bag could last you around SEVEN YEARS.
How do you use vermiculite in a fireplace?
It can be poured down your chimney to fill the gap between the flue pipe and your brickwork. It has a very high melting point of 1350°C which – when coupled with its insulating properties – means it can sit against your register plate and your flue and comfortably keep the heat where it should be.
Do you need Rockwool for gas fireplace?
Decorative ROCK WOOL is used on VENTED gas logs or to replace the wool on DIRECT VENT GAS FIREPLACES. Rock wool only glows when the flames come up through it, so there is no need to have it spread around any more than over the burner. **DO NOT USE ON VENT-FREE (UNVENTED) GAS APPLIANCES.
Can I use steel wool in a gas fireplace?
If the glass is dirty with a black coating or a white haze, you’ll need to do a heavy duty cleaning. If you are comfortable doing this, use either a polymesh scrubber or super fine grade #0000 steel wool that won’t scratch the glass and Dawn dishsoap. Apply a big squirt of Dawn to the inside of the fireplace glass.
