QA

Question: What Is Flash Mixing

Flash Mixing in Water Treatment Flash or rapid mixing stage consists in adding chemicals to raw water to foster coagulation, attracting particles which do not settle or are not filtered.

What is the purpose of flash mixing?

The primary purpose of flash mixing is to rapidly mix and uniformly (evenly) distribute the coagulant chemical throughout the water.

What is flash mixture?

Flash Mixer, Flocculators, Agitators A flash mixer is a chamber that contains mechanical stirrers, which is designed to assure fast, thorough, mixing of lime and alum for the purpose of creating floc. After screening out debris and testing the raw water, water treatment really begins at the flash mix chamber.

What’s a coagulant?

Coagulants are a substance which cause particles in a liquid to curdle and clot together. Coagulation treatment chemicals are used in effluent water treatment processes for solids removal, water clarification, lime softening, sludge thickening, and solids dewatering.

What happens if you add too much coagulant?

If too much or not enough coagulant is added, the removal of suspended matter will be less efficient. If too much coagulant is added, the cost of treating the water will also increase.

What is a flocculation tank?

The flocculation tank has wooden paddle-type mixers that slowly rotate on a horizontal motor-driven shaft. After flocculation the water flows into the sedimentation tanks. Some small water-treatment plants combine coagulation and sedimentation in a single prefabricated steel unit called a solids-contact tank.

What is mixing in water treatment?

Mixer. Coagulation/Flocculation is the process of creating conditions for particulates to come together to form flocs of solids and then settle in treated water.

How does a Clariflocculator work?

Clariflocculator is a combination of flocculation and clarification in a single tank. In the Clariflocculator, the water enters the flocculator, where the flocculating paddles enhance flocculation of the feed solids. As heavy particles settle to the bottom, the liquid flows radially upward in the clarifier zone,.

How could you remove heavy metals from polluted water economically?

Several methods have been used to remove heavy metals from contaminated water. They include chemical precipitation [17,18], ion exchange [19,20], adsorption [21,22], membrane filtration [23,24], reverse osmosis [25,26], solvent extraction [27], and electrochemical treatment [28,29].

What is flocculant for?

Used in a wide range of industries and applications, flocculants help to remove suspended solids from wastewater by aggregating contaminants into flakes or “flocs” that float to the surface of the water or settle at the bottom. They can also be used for lime softening, sludge thickening, and solids dehydration.

What chemicals are added during the flash mix of water treatment?

Flash Mixing in Water Treatment Attracted by coagulants, such as ferric chloride (FeCl3), PAC (poly aluminium chloride Al2Cl(OH)5), aluminium sulphate (Al2(SO4)3), these particles are then easy to agglomerate during the flocculation stage.

How do you create a Clariflocculator?

Design criteria of flocculator

  1. Depth of tank = 3 to 4.5 m.
  2. Detention period = 15 to 30 min.
  3. Velocity of flow = 0.2 to 0.8 m/s (normally 0.4m/s)
  4. Total area of paddle = 10 – 25% of cross-sectional area of tank.
  5. If the peripheral velocity of blade should be 0.2 to 0.6 m/s.

Which of these require a flash mixture prior to it?

Which of these require a flash mixer prior to it? Explanation: A clariflocculator requires a flash mixer prior to it. A clarifier requires both a flash mixer and flocculator prior to it. Clarifiers are used to remove suspended solids.

What are the various units in a Clariflocculator?

A solitary unit of Clariflocculator serves elements of both the clarifier and flocculator.It comprises of two concentric tanks – the internal tank fills in as a flocculation chamber while the external tank fills in as a clarifier chamber.

How do coagulants work?

Coagulants work by creating a chemical reaction, eliminating negative charges that cause particles to repel each other. The action of these bubbles forces clots or flocs of particles to the water surface where they can be skimmed off. Dissolved air flotation is an alternative to sedimentation.

How do you mix flocculant?

To optimize flocculant mixing system sizing, flocculant solutions are often designed to be mixed to 0.25-0.50% maximum concentration. Once dissolved, the flocculants will dilute readily with teed in water down stream of the flocculant feed pump to obtain the final target 0.1% concentration.

Which gas is released when alum is added to water?

Explanation: Carbon dioxide gas is released when alum is added to water, which is corrosive to metals.

Why do we use flocculation?

4 Flocculation. Flocculation is a process by which a chemical coagulant added to the water acts to facilitate bonding between particles, creating larger aggregates which are easier to separate. The method is widely used in water treatment plants and can also be applied to sample processing for monitoring applications.

What is the most common used coagulant?

1. Alum (aluminum sulfate), Al2(SO4)3. Still, the most common coagulant in the United States, it is often used in conjunction with cationic polymers.

Why is coagulant added to water?

Coagulant aid Chemicals (typically synthentic polymers) added to water to enhance the coagulation process. if an excess of alum is added so that the dosed water pH is less than 5.0, then the metal ions (Al3+) will directly ˜eutralize the negatively charged organic compounds and colloids in the raw water. 1.

What is RPM of blades in flash mixer?

Speed ranges from 172 rpm to 56 rpm based on the impellor diameter and tank size. Impellor Designs commonly used are Pitch Blade Turbine , Six Bladed Turbine or Radial Impellor. Flash Mixer Wetted Components are usually SS304 SS316 or Carbon Steel Rubberlined in construction.

What is the difference between rapid mixing tank and flocculation chamber?

Contact time in the rapid-mix chamber is typically 1 to 3 minutes. Flocculation, a gentle mixing stage, increases the particle size from submicroscopic microfloc to visible suspended particles. Microfloc particles collide, causing them to bond to produce larger, visible flocs called pinflocs.

What is the difference between coagulant and flocculant?

Flocculation is synonymous with agglomeration and coagulation / coalescence. Basically, coagulation is a process of addition of coagulant to destabilize a stabilized charged particle. Meanwhile, flocculation is a mixing technique that promotes agglomeration and assists in the settling of particles.

Why alum is used as coagulant?

When alum is added to water, it reacts with the water and results in positively charged ions. Coagulation removes colloids and suspended solids from the water. These particles have a negative charge, so the positively charged coagulant chemicals neutralize them during coagulation.

What are types of mixers used for flocculation in wastewater treatment?

Flocculation Process Using Static Mixers

  • Bitumen froth.
  • CO2 Mixer.
  • Crude oil metering.
  • Desuperheater.
  • Direct steam heating.
  • Heat Exchanger.
  • Inline static mixer.
  • Inline steam heater.