Table of Contents
The speed at which the induction motor work is known as the slip speed. The difference between the synchronous speed and the actual speed of the rotor is known as the slip speed. In other words, the slip speed shows the relative speed of the rotor concerning the speed of the field.
What is slip speed in 3 phase induction?
This speed difference is called slip. Therefore, the difference between the synchronous speed Ns of the rotating stator field and the actual rotor speed N is called slip. The slip increase with load and is necessary for torque production. Slip speed is equal to the difference between rotor speed and synchronous speed.
What is slip and synchronous speed?
Slip is the difference between the synchronous speed of a motor and its actual speed. Mathematically it is determined by. Slip = Synchronous Speed − Actual Speed. Using the example above for synchronous speed of a motor with four poles operating at 60 hertz, the value was calculated to be 1800 RPM.
What is slip speed how it is related to slip?
Slip increases with increasing load – providing a greater torque. It is common to express the slip as the ratio between the shaft rotation speed and the synchronous magnetic field speed. When the rotor is not turning the slip is 100 %.
What is the normal slip of an induction motor?
Because of this speed difference, the motor rotates at a speed slightly slower than the synchronous speed. Slip is normally expressed in percentage. Slip of a power induction motor is 2 to 3% when the motor is operated under the rated load.
How is slip in motor calculated?
What is Slip in an Induction Motor? Definition: In Induction Motor, a slip is a speed among the rotary magnetic flux as well as rotor expressed in terms of for every unit synchronous speed. It can be measured in dimensionless & the value of this motor cannot be zero. S = (Ns – Nr) / Ns. Slip = (Ns-Nr/Ns)*100.
What is slip speed?
The speed at which the induction motor work is known as the slip speed. The difference between the synchronous speed and the actual speed of the rotor is known as the slip speed. In other words, the slip speed shows the relative speed of the rotor concerning the speed of the field.
How is slip speed calculated?
Slip speed is the speed difference between the Synchronous speed and Rotor speed. Slip speed = Synchronous speed – Rotor speed = Ns -N. Slip, s = (Ns – N) / Ns.
What is full load slip?
The slip corresponding to full load speed of th motor is called full load slip. Example 1 : A 4 pole, 3 phase induction motor is supplied from Hz supply. Determine its synchronous speed. On full load, its speed is observed to be 1410 r.p.m. calculate its full load slip.
What happens when slip is zero?
Zero slip means that rotor speed is equal to synchronous speed. If rotor is rotating at synchronous speed in the direction of rotating magnetic field the, there will be no flux cutting action, no emf in the rotor conductors, no current in rotor bar conductor and hence no development of electromagnetic torque.
Can slip be negative?
If the rotor of an induction machine rotates above synchronous speed, slip is negative, as are torque, mechanical output power and air gap power. i.e. the machine is operating as a generator. Rotational losses are 2450W.
What is the importance of slip?
Slip creates a relative speed between the RMF and rotor. That keeps a torque continuously acting on it when the motor is running. So what would happen if slip becomes zero? Bcoz there will be no relative speed between RMF and rotor, and which will stop inducing rotor current.
What causes motor slip?
Slip depends on motor parameters The traditional way to control wound-rotor-induction-motor speed is to increase slip by adding resistance in the rotor circuit. The slip of low-hp motors is higher than that of high-hp motors because rotor-winding resistance is greater in smaller motors.
What is the role of slip in induction motor?
Slip of induction motor plays an important role in the operation of the induction motor. The torque produced by the induction motor is directly proportional to induction motor slip. When the motor is loaded, greater torque is required to drive the load, therefore, slip increases and rotor speed decreases slightly.
What is the slip of motor?
“Slip” in an AC induction motor is defined as: As the speed of the rotor drops below the stator speed, or synchronous speed, the rotation rate of the magnetic field in the rotor increases, inducing more current in the rotor’s windings and creating more torque.
What is synchronous speed?
Synchronous speed is a significant parameter for the rotating magnetic field-type AC motor. It is determined by the frequency and the number of magnetic poles. A collective name for the motors that run at the synchronous speed is the synchronous motor.
What is Torque slip?
The torque slip curve for an induction motor gives us the information about the variation of torque with the slip. The slip is defined as the ratio of difference of synchronous speed and actual rotor speed to the synchronous speed of the machine.
What is the difference between rotor speed and synchronous speed?
Induction motor with squirrel cage rotor has two different speeds. The synchronous speed refers to the stator rotating magnetic field, which depends on the number of poles and frequency. The other speed is the rotor’s. The rotor speed will be always slower than the stator speed, we call it slip.
Why there is no slip in synchronous motor?
Because the rotor turns at the same speed as synchronous speed (speed of the rotating magnetic field), there is no slip. The speed of rotation of the motor is constant in a synchronous motor, and does not vary with load, as in an induction motor.
What is slip in induction generator?
An induction generator produces electrical power when its rotor is turned faster than the synchronous speed. The motor normally turns slightly slower than the synchronous speed; the difference between synchronous and operating speed is called “slip” and is usually expressed as per cent of the synchronous speed.
