QA

Question: What Size Pipe For Tub Spout

Nearly all tub and shower faucets require a one-half inch diameter water supply pipe on both the hot and cold supplies.

What kind of pipe do you use for a tub spout?

Galvanized pipe is often used when a threaded pipe is required, since it’s a bit more durable than copper. Copper is a softer metal, and may not hold up as well against the potential abuse the spout could see.

How long should the pipe be for a tub spout?

There is no one correct pipe length for a tub spout. Because spouts are different sizes and the plumbing behind the wall is installed at different depths, it’s necessary to measure and purchase or make a pipe when installing a new spout.

Can I use PEX for a tub spout?

The tub spout can be copper, brass, or galvanized pipe. You cannot use pex because the pipe coming out of the valve needs to be able to support the weight of the tub spout and handle the abuse of pulling/ pushing down of the divirter built into the spout.

Is it OK to use CPVC for tub spout?

Most tub/shower faucets have a warning in there instructions to NOT use CPVC or PEX for the tub spout. Hope you haven’t closed the wall up because it will have to be changed. Re: Is CPVC appropriate for bath spout?.

Can I use CPVC for tub spout?

The spouts clamp onto the CPVC that comes through the tub wall via an allen head screw. Last night we opened the wall in one of the units, braced the shower valve and pipe from the spout with 2X4. It improved the movement of the spout somewhat, but not enough.

Are there different size tub spouts?

Tub spout tips: Although there are only two kinds of tub spout types (threaded and slip) there are several “sizes” (lengths) in each group. This is where your patience is important. Not every store carries every length in each type. When we refer to size we do not mean the overall length of the spout.

How far should pipe stick out for tub spout?

According to the installation manual for the spout, the nipple for the spout should be installed a min of 3/8″ to a max of 3/4″ past the finished wall. There is a pipe adapter that you screw onto the nipple.

Should I caulk around tub spout?

Bathtub faucets should always be caulked to avoid potential water damage. It can be a quick, easy and inexpensive task.

Can you use 3/4 PEX tub spout?

1. Use a 3/4″ PEX crimp to 1/2″ FIP adapter at the valve and a 3/4″ PEX crimp to 1/2″ FIP drop-ear elbow to hold the tub spout (with 3/4″ PEX between them, of course). The 3/4″ PEX crimp fittings may have a larger internal diameter than the 1/2″ Sharkbite as well.

Can you use sharkbite on tub spout?

A Sharkbite would hold and quite well. However, your tub spout will be able to spin round and round and round. You don’t want this effect with a tub spout so don’t use a Sharkbite. using a sharkbite would make removal impossibe, without destroying the spout.

Can you use PVC for tub spout?

PVC can be used only for drain lines (including indoors, despite what the answer below says). If you want to use it for your tub and shower drain, you can. CPVC can be used for water supply lines, and you can use it for the connection between the shower valve and the shower spout.

How high should the tub spout be above the tub?

The tub spout will generally be located 4 inches above the rim of the tub. In a shower only unit, the faucet is placed higher at 48 inches off the floor. The shower head normally is located 72 to 80 inches above the finished floor.

Is CPVC better than copper?

Energy efficiency: CPVC is more energy efficient than copper due to its improved thermal insulation properties, which also help to reduce condensation. Its insulating characteristics can signify long-term savings for building owners, keeping water hot for a longer period of time than metal tubing.

Are all tub spouts threaded?

A diverter spout can either be a slip-on or threaded, and the same thing goes for non-diverter spouts. Diverter and non-diverter tub spouts are the easiest to tell apart. Brass-adapted bathtub spouts can either be slip-on, threaded, diverter or non-diverter.

What is a slip fit connection on a tub spout?

A slip-fit spout has an internal assembly that slips over a copper pipe. The spout has an opening on the bottom side where a setscrew is tightened to hold the spout onto the copper pipe. A slip-fit spout does not contain threads.

How far into tub should tub filler be?

The water exit point of the spout of the tub filler should be about 6 inches above the tub. Any higher and there may be some unwanted water splashing on the side of the tub filler.