Table of Contents
When set to “unlocked”, the lock will unlock when you press the Schlage button (without entering a User Code). And when it’s set to “re-lock”, the lock returns to normal, meaning you’ll need to enter a valid code to unlock it. And if it’s in a horizontal position, it means the lock is set to “re-lock”.
Why does my Schlage lock opens without code?
It’s likely that when the unit was installed, the dead bolt was in the locked position. It needs to be installed (two sides joined together) when in the unlocked position. see less The Feb 23rd solution that everyone likes works by turning off the function that lets you lock without entering a code.
How do you disable Schlage unlock?
Delete ALL Access Codes Removes ALL access codes from the lock. Enable/Disable 1-Touch Locking When enabled: Press the Outside Schlage Button to lock the deadbolt. (Default setting). When disabled: Press the Outside Schlage Button and then enter an access code to lock the deadbolt.
Why is my Schlage keypad not working?
Your Schlage Connect Keypad may malfunction if the batteries are low. So if your keypad suddenly stops working, the first step to resolving this issue is to replace the batteries in your lock. So replace the batteries in your lock to see if that resolves the issue.
How do you reset a Schlage door?
Reset the Schlage lock by engaging the reset button if one is available, or by disconnecting the battery. Once the cover and housing are removed, if the button is there, simply press and hold it until the red light isn’t flashing anymore. Release it and wait until the lock resets itself and the light turns blue.
What is the programming code for Schlage locks?
Find the Default Programming Code You can find your Schlage Lock Programming Code on the front of the user manual—usually printed on a white label. If you don’t have the user manual, remove the lock from the door to find the Programming Code—printed on a white label on the back of the keypad assembly.
What does the Schlage button do?
Located on the outside of the door. Used to enter codes for programming and unlocking. The inside lever can be rotated at any time to retract the latch. The outside lever can be rotated at any time, but will only retract the latch when the lock is unlocked.
How do you program a Schlage Lock without code?
So first how to Reset Schlage Keypad lock? Disconnect the batteries. Press and hold the Outside Schlage Button. While holding the Outside Schlage Button, Reconnect the batteries. Release the Outside Schlage Button. To check that the lock was reset, press the Outside Schlage Button and enter one of the Default User.
How do you change the 4 digit code on a Schlage Lock without coding?
How to Change the 4 Digit Code on a Schlage Lock? Step 1: Press the Schlage button and number 1 at the same time. Step 2: Enter your new four-digit code. Step 3: Re-enter your new code.
What if I lost my Schlage programming code?
In fact, if you’ve lost your Programming Code, you can reset the lock and then use the default Programming Code to reprogram it. Note that after performing a factory reset, all previous programming will be erased/returned to factory default settings.
Why does my Schlage lock blinking red?
The Schlage button flashes red continuously. What does this mean? The battery is dead. You will need to replace the battery immediately.
Where is the master code on a Schlage Lock?
If you take the lock off of the door you will find the master code on a sticker on the back of the front of the lock. It is put there for security purposes as it requires you to have the access and ability to remove the lock from the door. The sticker will have three codes on it.
How do you unlock a Schlage keypad lock with a dead battery?
How do you unlock a Schlage Control lock that has a dead battery? Touch a new high-quality alkaline 9-volt battery to the contacts below the bolt throw. Wait for 1 red light and then 3 green lights with 3 beeps. Present a valid credential. Rotate the bolt throw away from the door edge. Replace the batteries.
Why is my Schlage lock beeping?
The beeper is there to confirm a successful unlocking or locking of the smart lock when using the keypad, as well as confirming each press of a number. The alarm is there to ward off any undesirables from entering your house without your permission.
Why does my Schlage lock battery keep dying?
For the most part, your Schlage Encode Lock may drain batteries fast because of weak Wi-Fi signal strength. The reason is still centered on Wi-Fi connectivity—read more about smart locks battery life. That said, on average, your Schlage Encode Lock batteries should last anywhere from 2 to 6 months—depending on usage.
How do I change the 4 digit code on my Schlage keypad?
Press the “Schlage” button and the number “1” button simultaneously to add/change a new entry code. Wait for the “Schlage” button to beep and flash three times. Enter a new four-digit code, and wait for the “Schlage” button to flash and beep three times. Re-enter the same four-digit code to confirm the change.
How do you change the 6-digit code on a Schlage Lock?
To change the six-digit programming code to one of your own choosing: Enter the existing six-digit code. Press the “Schlage” and then the “3” keys. When three orange flashes and three beeps occur, enter a new six-digit code. When three orange flashes and three beeps occur again, reenter the same new six-digit code.
What does the orange light on a Schlage Lock mean?
Orange flashes indicates lock is in the middle of a programming sequence.
