Table of Contents
How do you secure a closet rod to drywall?
To securely install a closet rod in drywall: Measure the size of the space where the closet rod will go. Buy a closet dowel rod and cut it to length. Choose a wall bracket that can be positioned so that you can screw it into wall studs. Mark the place where your first bracket will be installed. Drill pilot holes.
How do you support a closet rod?
Before installing a closet rod, it is best to place closet brackets in a position on the wall that allows for the most support. This will require a stud finder. Once wall studs have been located, closet rods and brackets can be screwed into the stud for optimal support.
Do closet rods need to be in studs?
Basic Installation It should be placed in front of a stud so you can screw into the stud to give it support. The typical height of a closet rod is from 60 to 80 inches, and both brackets should be at the same height, or the hooks you hang from the rod will slide to one end.
Do closet rods need support?
If your closet rod is longer than 48 inches, you will need support. However, regardless of how long the closet rod is, if you’re hanging heavier items such as winter jackets, then you will want support no matter what.
How many brackets do I need for closet rod?
Adjustable Closet Rod 1 TM Page 5 TM NOTE: Recommended 16″ bracket spacing. Maximum 32″ bracket spacing. First, measure the width of your closet. Measure 11-1/2″ from the rear closet wall.
How far apart are studs?
The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.
How do you hang a closet rod in plaster?
Drill a hole through the plaster wall, insert the toggle bolt through the rod holder, press the toggle through the drilled hole and tighten it down with a screwdriver. Hang the dowel rod on the closet rod holders.
How do you install drywall anchors?
How To: Use Drywall Anchors STEP 1: Choose the right drywall anchor. STEP 2: Twist the self-drilling wall anchor into drywall with moderate pressure. STEP 3: Turn the drywall anchor in until the lip is flush with the wall. STEP 4: Attach your rack or shelf to the wall by screwing into the drywall anchor.
How do you hang a closet rod from the ceiling?
Draw a straight line on the ceiling at right angles to the joists using a yardstick or straightedge tool as your guide. Make the line the length of the closet rod you purchased for the project. Put the line at least 12 inches from the back wall of the closet to allow room to hang clothes hangers on the clothes rod.
How much weight can a closet rod hold?
Aluminum Anodized Elite 1-5/16”: Up to 80 lbs. Stainless Steel 1-1/16”: Up to 95 lbs. Steel Polished Chrome Round 1-1/16”: Up to 110 lbs. Steel Polished Chrome Round 1-5/16”: Up to 170 lbs.
How far should closet rod be from shelf?
A minimum of 10 inches is best, but it’ll depend on the size of your hangers. If there is a shelf above the rod, determine the vertical distance from the rod to the shelf; two inches should be suffice.
How deep should closet rod be?
Opt for a closet rod depth of at least 12 inches. You can avoid this clothing disaster by mounting the rod at least 12 inches from the rear wall of the closet. Keep in mind that the average closet has a depth of 24 inches.
Can you use PVC for closet rods?
The PVC pipe was much less expensive than buying custom closet rods and it worked just fine as the closet rods. I put in an extra bracket to support the top rail and prevent sagging in the middle.
Can you use a tension rod in a closet?
They are cheap and totally removable. They are great for those awkward areas where nothing else fits, and don’t do any damage to walls, closets, or cabinets. Some of their uses are obvious, but there are others you might not have ever considered.
Why are there no studs in my closet?
Closet shelves are usually anchored to the wall where the mounting screws can grab wall studs. Thick plaster walls or paneling might bury studs too deep, making the studs inaccessible. If your walls are masonry, you likely don’t have studs at all.
Are there studs in the corners of closets?
There is usually a corner stud but if the next stud is within an inch or two they maybe left out. But one of the walls will always have a stud there.
How deep are studs behind drywall?
16 Inches On-Center.
Do studs have to be 16 on Center?
Why You Should Find Studs They’re always spaced either 16 or 24 inches on-center (measured from center to center) along the wall and run between the floor and ceiling. Drywall or lath (for plaster walls) attaches to the edge of the studs.
Do I need a stud finder?
It is commonly thought that you need to have a stud finder in order to find a stud in your drywall. But not all homeowners own a stud finder, and probably don’t need one often enough to justify the purchase. Most homes are built with 2×4 or 2×6 studs and studs can be found typically on the sides of windows or doors.
How much weight can plaster walls hold?
Both plaster and drywall can hold roughly the same amount of weight. A screw driven into a stud in both plaster and drywall can hold 80–100 pounds (36–45 kilos). Anchored screws or other fasteners set into the wall where there is no stud can hold up to 20 pounds (9 kilos).
