Table of Contents
What is the correct way to lay decking boards?
What is the correct way to lay decking? Any decking board manufacturer or professional will tell you: “The proper way to install a decking board is ridge side down.” The ridges are designed to allow for airflow, to stop moisture sitting in the ridge, and allow for a stronger structure.
Should deck boards be installed crown up or down?
Crown up is the preferred installation method, despite the potential for bark side down deck boards to experience shelling. Bark side down allows for the formation of a crown warp. Once the board forms a crown, there’s less potential for the wood to hold water, which could lead to the wood splintering and rotting.
Should you nail or screw deck boards?
The Consensus: For a deck build it’s best to use a combination of nails and screws. Screws are superior for laying down the decking. They hold things flush better and have a better fastener/tensile strength, which keeps boards from popping up over time.
Do you leave a gap between decking boards?
Proper Gap between Decking Boards When installing decking boards, make sure to leave 1/4 to 1/8 inch gaps in between them. This gap will make sure that the decking can breathe, have sufficient drainage, and make it easier to clean.
What is the proper spacing between deck boards?
Proper deck board spacing should have a 1/8-inch gap after the decking has dried out. If you install your decking using wet boards, pressure-treated decking that has not yet dried out, then you should install them with no gap as a gap will be created as they dry and shrink. Deck spacing isn’t anything to take lightly.
Should decking be laid grooved side up?
Grooved Decking Should Be Fitted Face Down It is entirely up to you whether you lay the boards grooved side up or down but, there are a few things you should bear in mind. Deck boards with grooves are designed to channel water away from the deck.
Should deck boards be parallel to the house?
The default direction decking runs on an attached deck is parallel with the house. A few reasons for this are deck framing construction, water runoff and appearance. Decking running parallel to the house is beneficial structurally, aesthetically and costwise.
Should deck boards be butted together?
We recommend butting treated deck boards together because as the moisture dries from the wood, the boards will shrink and naturally form gaps to allow water drainage. (Depending on moisture content, cedar, cypress and especially hardwood decking may require deliberate spacing for consistent joint sizes.)Jun 21, 2010.
Do you need to pre drill for deck screws?
Deck screws installed in the field, not close to the board’s end or edge, need not be predrilled. Predrilling is required near the end of deck boards to make room for the screw. As the screw is acting like a wedge, driving between the wood fibres. That screw pushes against the decking, splitting open the board.
Do you countersink deck screws?
A good countersink bit is necessary to fasten the wood decking. Tapered bits are preferable. They provide a good “slip hole” through the high-density hardwood decking and a smaller tapered hole in the deck joist or framing. Stainless steel deck screws are the only choice for fastening tropical hardwood decking.
Do you screw decking at every joist?
Each deck board should be fastened with two screws at each point where the board crosses a joist to ensure the stability and durability of your deck’s surface. Boards should be fastened to rim joists with three screws.
How do you stagger deck boards?
A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.
What happens if you don’t leave gaps in decking?
Without the right deck spacing, the boards may expand, cup, and buckle out of place. There is no reason to put a gap between the ends (also known as butt ends or butt joints) of wood deck boards. Wood, both softwood and hardwood, is dimensionally stable in length regardless of temperature, humidity or moisture content.
How many joists do I need for decking?
For example, when you space joists 16″ apart — which is standard for residential decks — a deck spanning 9 1/2′ would require 2-by-6 joists, a 13′ deck would need 2-by-8 joists and a 16′ deck calls for 2-by-10 joists.
How long should deck board screws be?
Deck screws measuring 2 ½ inches and 3 inches usually work best for fastening railings, deck boards, and joists, while 6-inch deck screws are necessary for 4×4 posts.
Where do you start laying deck boards?
In most cases, it’s best to start with a full board on the outside edge of the deck and work toward the house so the odd board is less visible. Then measure when you’re 4 to 5 ft. away from the house and adjust the gap sizes to be sure the last board is a consistent width.
How many screws do I need for decking?
The general rule of thumb for standard deck fasteners is 350 screws for every 100 square feet of decking, which is based on standard 6″ wide boards (5-1/2″ actual), and 16″ joist spacing.
Is it OK to flip your deck boards?
They are treated lumber.” You bet you can flip them. There’s no harm in doing so. While you’re at it, be sure to clean off any debris from the top of the support joists and check for rot at those locations.
