Table of Contents
Where should sprinkler control box be placed?
So, you’ll need to mount your controller within 6 feet of an electrical socket. You can mount it inside or out, as long as you keep it about 15 feet from other major appliances. Choose a spot that’s out of the rain and not in direct sun.
How do you find a hidden sprinkler valve?
1) Start in the Most Likely Places Probe the soil. Determine the irrigation valve area, and sift through the soil in that specific section of your property. Look for valves box covers. If valve boxes were set over the valves when the system was installed, they are most probably just under the surface.
Can you find sprinkler valves with a metal detector?
If your pipes are metal, the metal detector won’t tell you the location of the valve box, but it will tell you where the pipes are, so you can dig along the pipe to find the valve.
Where is my sprinkler master valve?
It is connected to the “master” or “pump” connection in your controller. For Generation 1 controllers, this is the blue terminal in the wall mount. For Generation 2 controllers, find the terminal marked “M”. In the image below, the master valve is in the small circular box to the left of the main sprinkler box.
How many zones can a sprinkler valve control?
Can I run more than one zone at a time? For the controllers HC, PROHC, HPC, you can only run a single zone at a time based on the power output available. Running multiple zones at once is usually not possible due water-pressure and flow limitations at residential properties.
Where is the main sprinkler system valve usually installed?
In newer lawn irrigation systems, the valves should be installed in valve boxes. These can often be seen easily. There is a single valve box located near where the irrigation pipes enter the ground in small yards.
How much does it cost to find sprinkler valves?
Most sprinkler repairs involve replacing sprinkler heads at $5 to $20 per head, or replacing valves at $20 to $40 per valve, not including the cost of labor.Sprinkler Systems Repair Costs. National Average Cost $212 Maximum Cost $500 Average Range $75 to $250.
How deep are sprinkler lines buried?
Dig for Your Sprinkler System The trenches will be relatively shallow, usually 6 to 12 inches deep, depending on your area’s freeze cycles and frost severity. The trench must also be deep enough to allow the sprinklers to retract underground to prevent breakage from lawn machines.
Where is the water supply valve?
The valve is typically located within 3 to 5 feet of where the water main enters the home. If you don’t find it on the front wall, check for a mechanical room, or near the water heater or furnace. In a crawl space or with slab construction, the shut-off valve may be right inside the crawl space.
Why is my sprinkler valve box full of water?
Why is my irrigation valve box full of water? An irrigation valve box can hold water after a heavy rain or when a valve, pipe or fitting is leaking. If the valve box is always full of water and you have ruled out irrigation leaks, check to make sure your French drain pipe isn’t clogged, if you have one.
What does a shut off valve do?
Shut off valves allow for the safe control of compressed air in pneumatic applications and are used in a range of industries. Shut off valves are also a useful accessory to stop the air supply in controlled conditions where a process must work correctly and safely.
Why do all my sprinkler zones come on at once?
Water is coming out of multiple zones at the same time: For the valves to stay open in one zone, while shutting outlets in other zones, there needs to be a minimum amount of water pushed through the valve. To investigate further causes and solutions, go to our FAQ page and look under “Indexing Valves.”May 20, 2020.
How many heads are in a zone?
At different pressures, the sprinkler head and nozzle will consume different amounts of water. For example, at 35 pounds per square inch (PSI) the 5000 Series Rotor using the 3.0 nozzle will use 3.11 gallons per minute (GPM). If your home’s water capacity was 10 GPM, you could place 3 heads per zone.
How many valves does a sprinkler system have?
Most automatic sprinkler systems are set up with two types of valves. A brass “gate valve” or “ball valve” is usually located right after the “tee” where the sprinkler system cuts off from the main source of water to the house.
How can I find my sprinkler lines without digging?
If you prefer to locate the lines and heads of your system without digging, rent a valve locator or even a metal detector and mark areas once found – better yet, call call 811, a federally mandated service, and ask someone to come out and locate the system for you.
How do I find buried sprinkler heads?
Many valves have metal parts you can locate by running the metal detector over the surface of the ground. Valves are located directly under sprinkler heads. Look for large, dry, brown spots in your lawn. This can indicate the location of a buried sprinkler head.
