Table of Contents
Measure from the wall behind the toilet to the center of one of the closet bolts (which hold the toilet down). If the toilet has four closet bolts, measure to the center of one of the rear ones. Then measure from the center of the mounting holes to the back of the new toilet you’re considering.
How do I know if my toilet is 10 or 12?
If your toilet has four bolts rather than the standard two, you’ll measure to the center of the rear bolts. The standard rough-in measurements are 10, 12 and 14 inches. If your measurement is in between these intervals, round your number down to the nearest standard measurement.
How do I know the rough-in size of my toilet?
The rough-in measurement of a toilet refers to the span between the wall behind the toilet and the center of the waste pipe. To measure the rough-in for your toilet, measure from the wall behind the toilet to the middle of the bolt caps (the caps holding your toilet to the floor).
Can you replace a 10-inch rough-in toilet with a 12-inch?
The rough-in for your bathroom plumbing should match the rough-in for the toilet. Even if a toilet is designed for a 10-inch rough-in, you can still install it in a space with a 12-inch rough-in.
What does 12-inch toilet mean?
The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″. Rear-outlet toilets are configured a bit differently.
Can you replace a 14-inch rough-in toilet with a 12-inch rough-in toilet?
Replace a 14-inch rough-in toilet with a 12-inch rough-in toilet. You can definitely replace a toilet with a rough-in of 14 inches with one with a rough of 12 inches. The problem with this method is that a 2-inch gap will be left between the toilet tank and the wall. Install an offset toilet flange.
What measurements are needed to replace a toilet?
Taking Measurements If your existing toilet has four bolts, measure to the center of the back bolts. This measurement is known as the rough-in measurement. For a standard toilet, the rough-in measurement should be between 11 inches and 13 inches.
Do toilets come in different sizes?
Are there different sizes of toilet? Yes, toilets come in a range of different sizes, that’s why it’s important to measure your existing toilet seat before you buy.
Is 1.6 or 1.28 toilet better?
A 1.28 GPF toilet uses 1.28 gallons of water per flush while a 1.6 GPF toilet uses 1.6 gallons per flush. 1.28 GPF toilets are therefore more water efficient than 1.6 GPF toilets but none is necessarily better at flushing than the other.
What is better round or elongated toilet?
Most people find elongated toilet bowls to be more comfortable, but in a small bathroom, a round bowl can save space. Elongated toilet bowls measure up to 31″ from the wall, while round fixtures max out at 28″. Because round bowls are less expensive than elongated bowls, they save a few dollars, too.
What does GPF mean in toilets?
The drive to innovate started in 1994, when the 1.6-gallons-per-flush (gpf) mandate went into effect, replacing the 3.5 to 5 gpf that had been the norm. The pressure to save water hasn’t let up. Now there are high-efficiency (HET) and ultra-high-efficiency (UHET) toilets that use a mere 1.28 and 0.8 gpf, respectively.
Can you use a 12 inch rough in toilet?
12 Inch Rough In Toilet A 12 inch rough in is the most common measurement in bathrooms. This size allows for the most variety in the shape of the bowl and style of the toilet you purchase. Even though this is the most standard measurement, don’t forgo measuring (at least twice) before buying a new toilet.
Can you move a toilet over a few inches?
Yes, you can actually move a toilet. Even moving a toilet by a few inches without having to make a new hole in the floor is possible. You can use an offset toilet flange to move the toilet by a couple of inches on any side. This will allow you to use the same wastewater line and in turn help to save you a lot of money.
How do I make sure my new toilet will fit?
If the base of the new toilet is shorter than the distance between the rear bolt holes and the wall, it should fit. In small bathrooms where space is tight, also measure from the sides of the flange bolts to the sidewalls or other objects to assure side-to-side clearance.
What is the standard size of toilet room?
The International Residential Code (IRC) sets the required minimum dimensions of a toilet room at 30 inches by 60 inches. However, for increased comfort and accessibility, the National Kitchen and Bath Association suggests a minimum of 36 inches by 66 inches.
What is standard toilet height?
Standard toilet height is around 14 1/2” from the floor to the bowl rim, without a toilet seat. In recent years toilet bowl height has increased to assist people with sitting and standing up, for the benefit of taller people, and those with physical handicaps and/or the elderly.
What is standard toilet seat size?
Typical width: 14″ – 14-1/2″ Typical round length: 16″ – 17″ Typical elongated/extended length: 18″ – 19″.
What is the difference between a 12 and 14 rough in toilet?
While 12-inch rough-ins are more generally common than 14-inch rough-ins, they both have their merits, and sometimes you need to reduce the space taken up behind the tank, which is where a 14-inch rough-in comes in handy. So if you’re looking to install 14-inch rough-in toilets, then you’ve come to the right place.
