Table of Contents
What is the correct way to lay decking boards?
What is the correct way to lay decking? Any decking board manufacturer or professional will tell you: “The proper way to install a decking board is ridge side down.” The ridges are designed to allow for airflow, to stop moisture sitting in the ridge, and allow for a stronger structure.
How should I stagger my deck boards?
A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.
Do you leave a gap between decking boards?
Proper Gap between Decking Boards When installing decking boards, make sure to leave 1/4 to 1/8 inch gaps in between them. This gap will make sure that the decking can breathe, have sufficient drainage, and make it easier to clean.
Should deck boards have a gap?
When using wood decking, you want a gap of at least 1/8 of an inch after your decking has dried out. If you’re using decking that’s already been dried out, you can leave a 1/8-inch gap when you install. Many decks will use “green” wood, or wood that hasn’t been dried down or kiln dried.
Is it OK to stagger deck boards?
Staggering the deck boards decreases the number of screws or nails going into one joist, which can weaken or rot the joist more quickly. Staggering the joints strengthens the deck by spreading the seams across more joists instead of placing the stress on only one.
Do deck boards need to end on joist?
All deck board should end on a joist, making sure to stagger deck board ends. While laying deck boards might seem easy and quick, you’ll want to take your time and do it right. One small mistake could result in you having to remove all the deck boards later to fix that extra-wide gap or crooked deck board.
How far should deck boards overhang?
The decking should overhang the joists between ¼ and 2 inches beyond the end joists and rim board. The amount of overhang you should leave depends on your deck board materials: Most wood decks: ¼” to 1 ¾”.
Do you screw decking at every joist?
Each deck board should be fastened with two screws at each point where the board crosses a joist to ensure the stability and durability of your deck’s surface. Boards should be fastened to rim joists with three screws.
What happens if you don’t leave gaps in decking?
Without the right deck spacing, the boards may expand, cup, and buckle out of place. There is no reason to put a gap between the ends (also known as butt ends or butt joints) of wood deck boards. Wood, both softwood and hardwood, is dimensionally stable in length regardless of temperature, humidity or moisture content.
Should I use deck boards or 2×6?
2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions. The primary function is to drain water from the deck. Gaps that are narrow (1/8”), can catch debris, specifically on top of the joists, and can be difficult to clean out.
Can I use 2×6 joists for a deck?
2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards. Most decking is not strong enough to support longer spans than 16″. Some builders reduce joist spacing to 12″ on center to strengthen the deck frame or to increase maximum allowable joist spans.
How thick should my deck boards be?
NOTE: Standard boards are often called a 5/4 board when referring to traditional lumber, which means the actual thickness is typically somewhere between 1” and 1 ¼”. Thicker boards are often called a 2 x 6 when referring to traditional lumber, which means the actual thickness is somewhere between 1.2” and 1.5”.
Where do you screw deck boards?
Make use to position the screws at least 15mm from the end of the deck board, or 20 mm from the edge of the deck board to avoid the risk of splitting the timber. Be sure to follow a minimum gap of 5mm to 6mm between individual deck boards.
How do you measure deck board spacing?
Square footage of board spacing = (S) x Length of deck Then multiply 0.26 feet by 16 feet to get 4.16 square feet, the total area of board spacing.
Should Trex be staggered?
Composite decking should not be staggered on a deck. Staggered decking requires butt joints, but composite decking expands and contracts with temperature changes making butt joints unsightly.
Which way should deck joists run?
On most decks, the decking boards run parallel to the house and across the joists (either perpendicular or at a 45 degree angle).
Which side of deck board should face up?
Lay deck boards so that the best-looking face is facing up! Wood is stable when its moisture content is held above 30%(fiber saturation point). As wood dries below 30% it shrinks. Wood shrinks and swells twice as much in the direction parallel to the growth rings as it does perpendicular to the growth rings.
Should you use screws or nails for a deck?
The Consensus: For a deck build it’s best to use a combination of nails and screws. Screws are superior for laying down the decking. They hold things flush better and have a better fastener/tensile strength, which keeps boards from popping up over time.
How far can a deck board overhang a joist?
The American Wood Council states that cantilevers are limited to 1/4 the span of the joists. Joist Spacing (o.c.) Maximum allowable overhang cannot exceed 1/4 of the actual main span.
