Table of Contents
A 6×6 post requires a 10″-diameter hole. Shovel a 6″ layer of gravel into the hole to provide drainage.
How many bags of concrete do I need for a 6×6 post?
How Much Concrete For A 6×6 Fence Post? Depth 50 Lb Bags 18″-21″ 6 22″-25″ 7 26″-28″ 8 28″-30″ 9.
How do you anchor a 6×6 post in the ground?
Step-By-Step Instructions: Dig the post hole, making it three times the width of the post and at a depth equal to 1/3 to 1⁄2 of the above-ground length of the post, plus 6″ (right). Pour 6″ of gravel or crushed stone into the bottom of the hole. Set the post in the hole.
How deep should an 8 foot post be in the ground?
In general, holes should be at least 3 feet deep for posts that extend 8 feet or more above ground level. Posts that extend 6 feet above ground level should have holes at least 2 1/2 feet deep.
How big of a hole do I need for a 4×4 post?
The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter. For a six-foot-high fence post, we would need a hole that’s 36 inches deep and 12 inches in diameter.
How deep do you bury a 6×6 post?
The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole.
How long will a treated 6×6 post last in the ground?
It will not last long (7 yrs max) if the bottom of the post is wet. If you place stone at the base of the post, it should last 20+ yrs. That’s common advice, and I believe it’s true for most soil types, but for rich clay that doesn’t drain well, it may make the situation worse: it will give water a place to pool.
What size post do you use for a 6 foot fence?
So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter. For our six-foot-high fence post, we would need a hole that’s 36 inches deep and 12 inches in diameter. The depth of your post hole plays a key role in the strength of your posts.
Can you put dry concrete in a post hole?
Fast-setting concrete is ideal for setting posts because there’s no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.
How many bags of concrete do I need for a post hole?
Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.
Is 2 feet deep enough for fence posts?
2 feet is the minimum depth that you should dig your fence post holes for. To dig the holes one-third to one-half of the post’s aboveground height, is a general formula. The deeper you dig the holes, the more stability your fence has.
How do I keep my post level while concrete dries?
You need to level it in two directions with a 4-foot level. After getting it straight in the first direction, hold one of the braces against the post and drive a single screw to connect the brace to the post. You can then level and brace the post in the other direction and begin filling the hole.
Can pressure treated posts be set in concrete?
Simply setting the posts in concrete does create a condition that will accelerate rot in the bottom of the posts. With pressure-treated posts, the rot will be slow. Concrete should be poured around the post – no concrete under the post.
How do I keep my 6×6 from rotting?
Applying a seal or stain to your wooden fence can help provide an additional level of protection against rot. You can choose to use a water repellent sealant to your wood to help keep rot-causing moisture out from your fences.
How strong is a 6×6 post?
However, an 8-foot 4×4 supports 6468-pounds and 2339-pounds at 14-feet, while a 6×6 is 18032 and 10550-pounds respectively – or 64% and 78% more load capacity.
Will pressure treated wood rot on concrete?
Treated wood shouldn’t rot in concrete because it should prevent both ingress of moisture and air. It often does because people set it in wet concrete which when dries shrinks from around the post and then allows both water and air to get between the two. The water gets trapped and sets the rotting process off.
What size post are used for pole barns?
Pole Barn: The term “Pole Barn” is often used in place of “Post Frame” however there is a distinction between the two. Pole Buildings use round poles whereas Post Frame Buildings use square or rectangular post, commonly 4×4, 4×6, 5×5, 6×6 or larger treated lumber or laminated columns.
Is it OK to set deck posts in concrete?
A deck post should always be placed on top of footing, not inside concrete because it can break. When concrete is poured around a deck post in this way, the post will rot due to moisture buildup by the soil.
How deep should anchor bolts be in concrete?
Steps to Installing Concrete Fasteners The hole should be drilled 1/4″ to 1/2″ deeper into the base material than the anchor will penetrate. This allows for any material to fall when the anchor is inserted into the hole. After the hole is drilled, it must be cleaned of all debris, material or dust.
