Table of Contents
Simply put, a roof rake edge is installed to cover the top edge of the siding where it meets the roof. You can think of it as a type of awning that is designed to allow water to flow off the roof and down onto the ground below, instead of down the side of your home.
What’s the difference between drip edge and rake edge?
What is a roof rake?
A roof rake is an excellent way to clear excess snow from the top of your home. Comprised of an extending handle and a blade, these simple tools allow you to remove snow from your roof while keeping both feet on the ground. Scoop blades are designed to be placed at the top of the roof and dragged towards the ground.
What part of a roof is a rake?
Rake—The slanting edge of a gable roof at the end wall of the house. Ridge—The horizontal line at the top edge of two sloping roof planes. Sheathing—The decking material (usually sheets of plywood), which is nailed to the rafters, and to which shingles or other outside roofing materials are secured.
What is a rake drip edge?
A drip edge on a roof is a corrosion resistant material that is applied at the eaves and rakes, under the shingles and against the fascia, to improve the efficiency of your roof’s water shedding ability.
Is rake edge necessary?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
Do gutters go on eaves and rakes?
Rain gutters should be positioned to extend beyond the eaves of a roof to collect rain and hail runoff. Gutters are placed on all sides of a home along the roof edge.
Is roof raking a good idea?
If your roof is flat or has a low slope, roof raking is definitely a must once the snow gets to be about 6 inches or more. If your roof has a higher pitch, it’s still something to consider, especially if the snow is wet and heavy and it is building up.
Why would you rake a roof?
Sometimes snow on your roof can be a good thing. Depending on snow density, your slanted roof may be able to safely support up to 2-4 feet of snow accumulation. The most common reason homeowners rake their roof is to prevent the creation (or reduce the impact) of ice dams.
Are roof rakes worth it?
Never, never use a roof rake or try to shovel snow off a slanted roof. It will do no good, will not cure ice dams, is extremely hazardous, and can harm asphalt shingles, and in your case, slate shingles. And it will take away snow that is a natural insulator as long as it stays on your house.
What is the difference between gable and rake?
Gable: The A-shaped side wall of the home that forms the peak of the roof is called the Gable. The home above has two gables, one on each end of the home. Rake: The rake of the roof is the part that ends over a gable end.
What is a rake overhang?
The American Wood Council’s 2012 Wood Frame Construction Manual defines rake overhang as “The horizontal projection of the roof measured from the outside face of the gable endwall to the outside edge of the roof.” Section 2.1. 3.4.
What are rake rafters supported by?
what is a gable/rake lookout? framing member fastened to a common rafter and cantilevered outward over the gable rafter to support the rake rafter. where are the gable studs? vertical studs extending from the cap plate on the wall to the underside of the gable rafter.
Does drip edge go around entire roof?
Drip edge is installed around the whole perimeter of the roof. It is used to hold the underlayments down and create a watertight seal around the edge of the roof. Only the face of the metal is seen and is usually just white one to one and half inch stripe located right under the shingles and above the fascia.
Do gutters need to be removed to install drip edge?
The ONLY and VERY IMPORTANT exception is 4” flanged gutter, those should ALWAYS be removed when the roof is stripped. Once they are locked on with new, independent drip edge and shingles, they can never be re-pitched, a common maintenance item for gutters.
What is the underside of a roof overhang called?
Soffit: The underside of the eaves, or roof overhang, which can be enclosed or exposed. Soffit Vent: An intake vent in the soffit area of the house that provides attic venting at a lower portion of the roof deck and good circulation with other forms of venting such as ridge or roof vents; also called an intake vent.
What are Gables on a roof?
Gabled roofs are the kind young children typically draw. They have two sloping sides that come together at a ridge, creating end walls with a triangular extension, called a gable, at the top.
How far should metal roof overhang?
A typical metal roof overhang may be 2 to 4 inches, or even less. Some slight overhang is recommended, in conjunction with a drip edge flashing, to prevent water from getting under the roofing and onto underlying wood.
Why do houses in Texas not have gutters?
That’s because water from rain or snow that is allowed to flow over your roof onto the ground surrounding your home can damage your foundation, which can be a costly repair.
What is rake soffit?
It covers the top edge of the siding where it meets the roof, or sometimes the soffit, depending on if there is an overhang or not. A rake board prevents rain from running the wrong way that could ultimately cause damage to your roof’s interior due to a leak.
