Table of Contents
Simply put, a roof rake edge is installed to cover the top edge of the siding where it meets the roof. You can think of it as a type of awning that is designed to allow water to flow off the roof and down onto the ground below, instead of down the side of your home.
What is the difference between drip edge and rake edge?
What is the rake line of a roof?
Well, the rake of a roof is the exposed portion on the sides of a gable roof that extends from the eave to the ridge of the sloped sides. The rake of a roof covers the top edge of the roof. This is also an area of the roof where leaks can often occur.
What is a roof rake used for?
A roof rake is an excellent way to clear excess snow from the top of your home. Comprised of an extending handle and a blade, these simple tools allow you to remove snow from your roof while keeping both feet on the ground.
What are the edges of a roof called?
Eave: A roof edge that extends past the exterior wall line at the bottom of a slope. Fascia: Vertical roof trim located along the perimeter of a building, usually below the roof level, to cover the rafter tails at the eaves and to seal off the top of the siding along the rake; also called gutter boards.
Is rake edge necessary?
Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.
What is rake overhang?
The American Wood Council’s 2012 Wood Frame Construction Manual defines rake overhang as “The horizontal projection of the roof measured from the outside face of the gable endwall to the outside edge of the roof.” Section 2.1. 3.4.
When should you rake a roof?
If your roof is flat or has a low slope, roof raking is definitely a must once the snow gets to be about 6 inches or more. If your roof has a higher pitch, it’s still something to consider, especially if the snow is wet and heavy and it is building up.
Where are the rakes on a roof?
Rake—The slanting edge of a gable roof at the end wall of the house. Ridge—The horizontal line at the top edge of two sloping roof planes.
What is rake drip edge?
What is a drip edge? A drip edge on a roof is a corrosion resistant material that is applied at the eaves and rakes, under the shingles and against the fascia, to improve the efficiency of your roof’s water shedding ability.
Are roof rakes worth it?
Never, never use a roof rake or try to shovel snow off a slanted roof. It will do no good, will not cure ice dams, is extremely hazardous, and can harm asphalt shingles, and in your case, slate shingles. And it will take away snow that is a natural insulator as long as it stays on your house.
Does roof rake damage shingles?
Use a snow rake for pitched roofs (available at most hardware stores) to remove snow from your roof. Start from the edge and work your way into the roof. Try to shave the snow down to a 2 or 3 inches on the roof instead of scraping the roof clean, which will risk damage to your shingles or other roof covering.
What is the difference between gable and rake?
Gable: The A-shaped side wall of the home that forms the peak of the roof is called the Gable. The home above has two gables, one on each end of the home. Rake: The rake of the roof is the part that ends over a gable end.
What is the rake board on a house?
March 22, 2013. Rake board gives your roof and the eaves the finished look you want to really enhance the ambiance of the exterior appearance. This is the name given to the board that you place on along the slope of the roof of your home.
How do you measure a roof rake?
Place the end of the level against the bottom edge of a roof rafter and hold it perfectly level. Measure from the 12-inch mark on the level vertically to the bottom edge of the rafter. That measurement is the number of inches that the roof rises in 12 inches. Locate a rake board that is readily accessible to you.
What are the edges of a flat roof called?
Roof edge (or eaves edge) All the boards running along the edge of the roof or eaves. Also known as a fascia.
What is the rake of a roof made of?
Defining the Rake of a Roof Specifically, it’s the exposed part of a gabled roof that extends from an eave to the ridge of the roof’s sloped sides. It covers the top edge of a roof and is typically cut from a variety of roofing materials. Concrete or PVC, cedar, pine, and smartboard are all common candidates.
Do gutters go on eaves and rakes?
Rain gutters should be positioned to extend beyond the eaves of a roof to collect rain and hail runoff. Gutters are placed on all sides of a home along the roof edge.
